SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety
aboutharshith17-cpu·SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System-for-Soldier-Safety·hardware/kicad/sentinelseye.kicad_sch.xml
About the SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety PCB
SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety is an open source ESP32 PCB design by aboutharshith17-cpu, published on GitHub under the MIT license. It is a board, with 34 components from 34 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the OV5647, MAX98357A, DRV2605, MCP73831 and CW2015. By type, the board carries 7 ICs, 6 connectors, 5 capacitors, 4 resistors, 3 diodes and 2 crystals.
It belongs with the iot & wireless, audio and wearables designs in this gallery.
From the project
AI-enabled embedded wearable integrating computer vision, CNN-based fatigue classification, and real-time eye-state monitoring for soldier safety.Optimized low-latency inference, embedded alert mechanisms, and power-efficient edge intelligence for continuous fatigue detection.
An embedded wearable system that integrates computer vision, convolutional neural network-based fatigue classification, and real-time eye-state monitoring. The system is designed for continuous operation in mission-critical environments where sustained attention is required.
- Microcontroller: ESP32-S3-WROOM-1 (240MHz, 8MB PSRAM, WiFi/BT/BLE) - Camera: OV5647 5MP MIPI camera, 15 FPS capture - Audio: MAX98357A Class-D I2S amplifier with 1W speaker - Haptic: DRV2605 ERM/LRA haptic driver with 10mm coin motor - Power: 3.7V 2000mAh LiPo battery with MCP73831 charger and CW2015 fuel gauge - PCB…
Main components on the SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety
SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety bill of materials (BOM)
34 components, 34 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 Espressif | ESP32-S3-WROOM-1 | U1 |
| 1 | OV5647 Module:OV5647_5MP | OV5647_5MP | U2 |
| 1 | MAX98357A SOIC-8-3.9x4.9mm | SOIC-8-3.9x4.9mm | U3 |
| 1 | DRV2605 DRV2605 | DRV2605 | U4 |
| 1 | MCP73831 SOT-23-5 | SOT-23-5 | U5 |
| 1 | CW2015 SOT-23-6 | SOT-23-6 | U6 |
| 1 | NCP1117 TO-220-3 | TO-220-3 | U7 |
| 1 | Haptic Motor 10mm ERM | 10mm ERM | M1 |
| 1 | Crystal 40MHz XTAL_3225_4P | XTAL_3225_4P | Y1 |
| 1 | Crystal 32.768kHz XTAL_3215 | XTAL_3215 | Y2 |
| 1 | USB-C USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_USB2.0_16P | J1 |
| 1 | Camera Connector FFC_Hirose_FH26-15S-0.5SH | FFC_Hirose_FH26-15S-0.5SH | J2 |
| 1 | Speaker 2-pin JST_XH_2.0mm | 2-pin JST_XH_2.0mm | J3 |
| 1 | Haptic Connector 2-pin JST_XH_2.0mm | 2-pin JST_XH_2.0mm | J4 |
| 1 | Battery JST_PH_2.0mm_2P | JST_PH_2.0mm_2P | J5 |
| 1 | Antenna Connector IPEX_MHF4_2.0mm | IPEX_MHF4_2.0mm | J6 |
| 1 | Antenna AN-TS02 | AN-TS02 | ANT1 |
| 1 | LiPo LiPo_2x25mm | LiPo_2x25mm | BT1 |
| 1 | 500mA 1206_L | 1206_L | F1 |
| 1 | Speaker Speaker_8OHM_1W | Speaker_8OHM_1W | SP1 |
Show 14 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Reset TS-1089-E-C | TS-1089-E-C | SW1 |
| 1 | Green LED_0603 | LED_0603 | D1 |
| 1 | Red LED_0603 | LED_0603 | D2 |
| 1 | ESD Protection DO-214AA-2 | DO-214AA-2 | D3 |
| 1 | 10UH 10uH L_1812 | L_1812 | L1 |
| 1 | 100NF 100nF C_0402 | C_0402 | C1 |
| 1 | 10UF 10uF C_0402 | C_0402 | C2 |
| 1 | 22PF 22pF C_0402 | C_0402 | C3 |
| 1 | 47UF 47uF C_0805 | C_0805 | C4 |
| 1 | 1UF 1uF C_0402 | C_0402 | C5 |
| 1 | 10K 10k R_0402 | R_0402 | R1 |
| 1 | 4.7K 4.7k R_0402 | R_0402 | R2 |
| 1 | 330 R_0402 | R_0402 | R3 |
| 1 | 100K 100k R_0402 | R_0402 | R4 |
SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety design files
The KiCad project lives in the aboutharshith17-cpu/SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System-for-Soldier-Safety repository on GitHub; these links point at the commit this page was built from.
SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety: common questions
What microcontroller does the SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety use?
The SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How many components are on the SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety?
34 components, from 34 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety design files?
From the aboutharshith17-cpu/SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System-for-Soldier-Safety repository on GitHub, which has a netlist and the BOM; the links under Design files point to each one.
Can I use the SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety design in my own project?
Yes, under the terms of its MIT license, which aboutharshith17-cpu chose for the repository.
Can I test firmware for the SentinelEye-AI-Powered-Wearable-Drowsiness-Detection-System for-Soldier-Safety without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k