Hyperion controller
adamhrnciar·hyperion-controller·hardware/hyperion.kicad_pcb
About the Hyperion controller PCB
Hyperion controller is an open source Raspberry Pi PCB design by adamhrnciar, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 34 × 28 mm, with 64 components from 35 distinct parts.
Its main chip is the RP2354A, from the Raspberry Pi family. Other key parts include the DRV8231ADSGR, LMR51610YDBVR, ME6211C33M5G-N and LSM6DSV32XTR. By type, the board carries 35 capacitors, 14 resistors, 6 ICs, 5 diodes, 2 inductors and 1 transistor.
It belongs with the robotics & motion, power & battery and sensors designs in this gallery.
From the project
Open-source controller for 150 g antweight combat robots: RP2354A, 2x DRV8231A, 2-4S, ELRS/CRSF/SBUS/iBUS/PPM input, IMU. KiCad 10, CERN-OHL-S-2.0.
Open-source all-in-one controller for 150 g antweight combat robots. It combines an RC receiver input, two brushed drive motor drivers, power handling and an IMU on a 34 × 28 mm 2-layer board.
Designed by Team Hyperion (Faculty of Electrical Engineering and Communication, Brno University of Technology) for the Czech Combat Robot League (Česká liga bojových robotů, FLS Battlebots).

Main components on the Hyperion controller
Hyperion controller bill of materials (BOM)
64 components, 35 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | RP2354A | RP2354A_QFN-60_CircuitNinja | U1 |
| 2 | DRV8231ADSGR | Texas_DSG0008A_WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm | U2, U3 |
| 1 | LMR51610YDBVR | SOT-23-6 | U4 |
| 1 | ME6211C33M5G-N ME6211C33M5G | SOT-23-5 | U5 |
| 1 | LSM6DSV32XTR | LGA-14_3x2.5mm_P0.5mm_CircuitNinja | U6 |
| 1 | AON7403 (TECH PUBLIC) AON7403 | AON7403_PowerPAK1212-8_GSD | Q1 |
| 1 | ABM8-272-T3 12MHz ABM8-272-T3 | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | SMF18A (JSCJ) SMF18A | D_SOD-123F | D1 |
| 1 | BZT52C12 (MDD) BZT52C12 | D_SOD-123 | D2 |
| 1 | B5819W (MDD) B5819W | D_SOD-123 | D3 |
| 1 | KT-0603R Red | LED_0603_1608Metric | D4 |
| 1 | P2-0603G1TS2-06T-002 Green | LED_0603_1608Metric | D5 |
| 1 | AOTA-B201610S3R3-101-T 3.3uH AOTA-B201610S3R3-101-T | L_Murata_DFE201610P | L1 |
| 1 | FNR4030S100MT 10uH FNR4030S100MT | L_Changjiang_FNR4030S | L2 |
| 4 | CL31B106KBHNNNE 10uF 50V X7R | C_1206_3216Metric | C1, C2, C31, C33 |
| 1 | RVE100UF35V67RV0072 (optional, hand-wired) 100uF 35V elec DNP (wire to pads) | C_1206_3216Metric | C3 |
| 1 | HGC1206R7475K500NSPJ 4.7uF 50V X7R | C_1206_3216Metric | C4 |
| 5 | 0603B104M500NT 100nF 50V | C_0603_1608Metric | C5, C6, C8, C30, C32 |
| 1 | CL21A226MPQNNNE 22uF 10V | C_0805_2012Metric | C7 |
| 1 | CL10A106KP8NNNC 10uF 10V | C_0603_1608Metric | C9 |
Show 15 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | TCC0603X5R105K160CT 1uF 16V | C_0603_1608Metric | C10, C11 |
| 1 | CL10A475KO8NNNC 4.7uF 16V | C_0603_1608Metric | C12 |
| 14 | CL05B104KO5NNNC 100nF | C_0402_1005Metric | C13, C14, C15, C16, C17, C18, C19, C20 +6 |
| 3 | CL05A475MP5NRNC 4.7uF 10V | C_0402_1005Metric | C22, C23, C24 |
| 2 | 0402CG150J500NT 15pF | C_0402_1005Metric | C28, C29 |
| 1 | 0603WAF4702T5E 47k | R_0603_1608Metric | R1 |
| 1 | 0603WAF1153T5E 115k 1% | R_0603_1608Metric | R2 |
| 1 | 0603WAF2202T5E 22k 1% | R_0603_1608Metric | R3 |
| 1 | 0603WAF1003T5E 100k | R_0603_1608Metric | R4 |
| 1 | 0603WAF2202T5E 22k | R_0603_1608Metric | R5 |
| 1 | 0603WAF1001T5E 1k | R_0603_1608Metric | R6 |
| 1 | 0402WGF330JTCE 33R | R_0402_1005Metric | R7 |
| 3 | 0402WGF1001TCE 1k | R_0402_1005Metric | R8, R11, R12 |
| 2 | RC-02K27R0FT 27R | R_0402_1005Metric | R9, R10 |
| 2 | 0603WAF1101T5E 1.1k 1% | R_0603_1608Metric | R13, R14 |
Hyperion controller design files
The KiCad project lives in the adamhrnciar/hyperion-controller repository on GitHub; these links point at the commit this page was built from.
Hyperion controller: common questions
What microcontroller does the Hyperion controller use?
The Hyperion controller is built around the RP2354A, from the Raspberry Pi family.
How big is the Hyperion controller PCB?
The Hyperion controller measures 34 × 28 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Hyperion controller?
64 components, from 35 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Hyperion controller design files?
From the adamhrnciar/hyperion-controller repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Hyperion controller design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which adamhrnciar chose for the repository.
Can I test firmware for the Hyperion controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
Similar boards
Raspberry Pi
Open source rover
nasa-jpl
220 × 178 mm144 parts2LApache-2.09.7kRaspberry Pi
Iot
dotnet
56 × 65 mm24 parts2LMIT2.4kRaspberry Pi
SPIRIT
SPIRIT-org
82 × 155 mm130 parts6LCERN-OHL-S-2.01.3kRaspberry Pi
CM5RevEng
schlae
55 × 40 mm417 parts10LNo license1.0kRaspberry Pi
Haxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license673Raspberry Pi
Phased
Neumi
75 × 100 mm71 parts2LNo license507