18 open source boards using the DRV8231ADSGR

Real designs built with the DRV8231ADSGR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

18 boardsClear filters|Most starred

How designs wire the DRV8231ADSGR

Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the DRV8231ADSGR connects to, and the resistors, capacitors and other passives placed on it.

  • The IPROPI_1 pin has a resistor to GND on 10 of 11 designs, most often 1 kΩ (then 3.3 kΩ).
  • The VM_5 pin has a capacitor to GND on 10 of 10 designs, most often 10 µF (then 100 nF).
  • The IPROPI_1 pin has a series resistor on 6 of 11 designs, most often 220 kΩ.
  • The OUT1_6 pin has a series resistor on 6 of 10 designs, most often 33 kΩ.
IPROPI_1pin 1Connected to: Signal 91%
  • Resistor to GND on 91% · 1 kΩ (4), 3.3 kΩ (3), 1.1 kΩ (2)
  • Series resistor on 55% · 220 kΩ (6)
VREF_4pin 4Connected to: VREF 70% · a signal 30%
  • Decoupling capacitor on 30% · 100 nF (3), 10 µF (1), 22 µF (1)
VM_5pin 5Connected to: A connector 40%, NCP730BMT330TBG 30%, DRV8231ADSGR 20% · VBAT 20%
  • Capacitor to GND on 100% · 10 µF (15), 100 nF (10), 22 µF (5)
OUT1_6pin 6Connected to: A connector 90%
  • Series resistor on 60% · 33 kΩ (6)
GND_1_7pin 7Connected to: GND 100%
OUT2_8pin 8Connected to: A connector 90%
  • Series resistor on 60% · 33 kΩ (6)
GND_2_9pin 9Connected to: GND 100%

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Osc dev v006 by OpenServoCore, RTB D16 by git4dcc, MagMouse by sbarisic and RTB D20 by git4dcc.

The DRV8231ADSGR in open source designs

The gallery holds 18 open source boards using the DRV8231ADSGR from 11 GitHub repositories; a typical one measures about 50 × 40 mm and carries around 69 components.

89% use four copper layers or more, and 67% carry an open source license.

The most starred is Osc dev v006 by OpenServoCore.

Microcontrollers on boards using the DRV8231ADSGR

What boards using the DRV8231ADSGR are built for

DRV8231ADSGR: common questions

Where can I find a DRV8231ADSGR reference design?

Each of the 18 boards on this page is a real design using the DRV8231ADSGR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the DRV8231ADSGR IPROPI_1 pin?

The IPROPI_1 pin has a resistor to GND on 10 of 11 designs, most often 1 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 11 open source designs using the DRV8231ADSGR.

How is the DRV8231ADSGR VM_5 pin connected?

The VM_5 pin has a capacitor to GND on 10 of 10 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 11 open source designs using the DRV8231ADSGR.

What resistor goes on the DRV8231ADSGR OUT1_6 pin?

The OUT1_6 pin has a series resistor on 6 of 10 designs, most often 33 kΩ. Counted from the KiCad layouts of 11 open source designs using the DRV8231ADSGR.

What parts are used alongside the DRV8231ADSGR?

The AVR-64DA32, AVR64DD28-I_STX, NCP730BMT330TBG and NCP730BMT500TBG appear in the most repositories here.

Which microcontrollers do boards using the DRV8231ADSGR use?

Most are built on ESP32 (5), RP2040/RP2350 (4), AVR/Arduino (1) and Raspberry Pi (1).

How big is a typical board using the DRV8231ADSGR?

The median is 50 × 40 mm, and 11% are two-layer designs.

What is the most popular open source board using the DRV8231ADSGR?

By GitHub stars, Osc dev v006 by OpenServoCore, with 34 stars.

Can I simulate one of these boards using the DRV8231ADSGR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part