ESP32-Development-Board
akashh218·ESP32-Development-Board·esp32/esp32.kicad_pcb
About the ESP32-Development-Board
ESP32-Development-Board is an open source ESP32 PCB design by akashh218, published on GitHub. It is a 2-layer board measuring 36 × 52.5 mm, with 27 components from 15 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the CP2102N-Axx-xQFN28 and AMS1117-3.3. By type, the board carries 9 resistors, 7 capacitors, 3 ICs, 3 connectors, 3 diodes and 2 transistors.
It belongs with the iot & wireless, robotics & motion and dev boards & breakouts designs in this gallery.
From the project
Custom ESP32 development board with USB-C, GPIO expansion, sensor interfaces, and motor control support for IoT, robotics, and embedded applications.
This project is a custom ESP32-WROOM development board designed for embedded systems, IoT applications, robotics, and rapid prototyping. The board integrates essential support circuitry required for programming, debugging, power management, and peripheral interfacing, providing a reliable platform for ESP32-based development.
ESP32-WROOM module USB Type-C interface for power and programming USB-to-UART converter for firmware upload and serial debugging 3.3V regulated power supply Reset and Boot buttons GPIO breakout headers I²C expansion support UART communication interface Motor driver…
Main components on the ESP32-Development-Board
ESP32-Development-Board bill of materials (BOM)
27 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32 | U1 |
| 1 | CP2102N-Axx-xQFN28 | QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm | U2 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U3 |
| 2 | NPN | SOT-23 | Q3, Q4 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_GCT_USB4085 | J1 |
| 1 | RIGHT | PinHeader_1x14_P2.54mm_Vertical | J2 |
| 1 | LEFT | PinHeader_1x14_P2.54mm_Vertical | J3 |
| 1 | D_Schottky | D_SOD-123 | D1 |
| 2 | LED | LED_0402_1005Metric | D2, D3 |
| 4 | 0.1µF | C_0402_1005Metric | C1, C2, C5, C6 |
| 3 | 10µF | C_0805_2012Metric | C3, C4, C7 |
| 2 | 5.1kΩ | R_0402_1005Metric | R1, R2 |
| 5 | 10K | R_0402_1005Metric | R3, R4, R5, R6, R7 |
| 1 | 330Ω | R_0402_1005Metric | R8 |
| 1 | 1K | R_0402_1005Metric | R9 |
ESP32-Development-Board design files
The KiCad project lives in the akashh218/ESP32-Development-Board repository on GitHub; these links point at the commit this page was built from.
- Layoutesp32/esp32.kicad_pcb
- Schematicesp32/esp32.kicad_sch
ESP32-Development-Board: common questions
What microcontroller does the ESP32-Development-Board use?
The ESP32-Development-Board is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the ESP32-Development-Board?
The ESP32-Development-Board measures 36 × 52.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32-Development-Board?
27 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the ESP32-Development-Board design files?
From the akashh218/ESP32-Development-Board repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the ESP32-Development-Board design in my own project?
The repository has no license, so all rights stay with akashh218. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ESP32-Development-Board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k