Epaper badge
aks4896·epaper_badge·hw/bsides_badge.kicad_pcb
About the Epaper badge PCB
Epaper badge is an open source ESP32 PCB design by aks4896, published on GitHub under the MIT license. It is a 2-layer board measuring 100 × 100 mm, with 79 components from 30 distinct parts.
Its main chip is the ESP32-WROOM, from the ESP32 family. Other key parts include the ETA1036-33S2F-T, CJT1117-3.3 and FT230XS. By type, the board carries 24 capacitors, 23 resistors, 15 test points, 4 ICs, 3 connectors and 3 diodes.
It belongs with the displays & leds and wearables designs in this gallery.
From the project
Project to create conference badge using epaper display
Main components on the Epaper badge
Epaper badge bill of materials (BOM)
79 components, 30 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM | ESP32-WROOM | U1 |
| 1 | ETA1036-33S2F-T | SOT-23-5 | U2 |
| 1 | CJT1117-3.3 | SOT-223-3_TabPin2 | U3 |
| 1 | FT230XS | SSOP-16_3.9x4.9mm_Pitch0.635mm | U4 |
| 1 | 2N7002 | SOT-23 | Q1 |
| 1 | CJ2302 | SOT-23 | Q2 |
| 1 | USB_B | USB_Micro-B_Molex_47346-0001 | J3 |
| 1 | Micro_SD_Card | MICRO-SD9+4P-SMD-16.1X14.5X1.85MM | J4 |
| 1 | CONN_01X24 | Hirose_FH12-24S-0.5SH_1x24_P0.5mm_Horizontal | J5 |
| 1 | Battery_Cell | Keystone_2466_1xAAA | BT1 |
| 1 | SW_Push | SW_SPST_SKQG | SW1 |
| 15 | TEST_POINT | SolderWirePad_single_0-8mmDrill | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 +7 |
| 3 | B540 | D_SOD-123 | D1, D2, D3 |
| 1 | 10uH | L_Taiyo-Yuden_NR-60xx_HandSoldering | L1 |
| 1 | 470@100MHz | L_0805 | L2 |
| 1 | 22uH | L_Taiyo-Yuden_NR-40xx_HandSoldering | L3 |
| 10 | 1.0uF | C_0603 | C1, C16, C17, C18, C19, C20, C21, C22 +2 |
| 5 | 0.1uF | C_0603 | C2, C4, C5, C12, C14 |
| 3 | 4.7uF | C_0603 | C3, C13, C15 |
| 2 | 22uF | C_0805 | C6, C8 |
Show 10 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 22uF | CP_Tantalum_Case-A_EIA-3216-18_Reflow | C7 |
| 2 | 47pF | C_0603 | C9, C10 |
| 1 | 10uF | C_0603 | C11 |
| 9 | 10k | R_0603 | R1, R2, R6, R15, R16, R17, R18, R19 +1 |
| 1 | 470 | R_0603 | R3 |
| 1 | 1k | R_0603 | R4 |
| 1 | 1M | R_0603 | R5 |
| 2 | 22 | R_0603 | R7, R8 |
| 8 | 0 | R_0603 | R9, R10, R11, R12, R13, R14, R21, R22 |
| 1 | ?? | R_0603 | R23 |
Epaper badge design files
The KiCad project lives in the aks4896/epaper_badge repository on GitHub; these links point at the commit this page was built from.
Epaper badge: common questions
What microcontroller does the Epaper badge use?
The Epaper badge is built around the ESP32-WROOM, from the ESP32 family.
How big is the Epaper badge PCB?
The Epaper badge measures 100 × 100 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Epaper badge?
79 components, from 30 distinct parts. The full bill of materials is listed on this page.
Where can I download the Epaper badge design files?
From the aks4896/epaper_badge repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Epaper badge design in my own project?
Yes, under the terms of its MIT license, which aks4896 chose for the repository.
Can I test firmware for the Epaper badge without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k