Bicep

albachten·bicep

Bicep PCB layout, top view — open source Microchip SAM board by albachten

About the Bicep PCB

Bicep is an open source Microchip SAM PCB design by albachten, published on GitHub under the CC0-1.0 license. It is a 4-layer board measuring 70 × 85 mm, with 55 components from 39 distinct parts.

Its main chip is the ATSAMD21G18A-A, from the Microchip SAM family. Other key parts include the RFM95W-915S2, MCP73831-2 and AP2112K-3.3. By type, the board carries 13 capacitors, 12 connectors, 12 resistors, 6 LEDs, 4 ICs and 2 transistors.

It belongs with the rf & radio and power & battery designs in this gallery.

From the project

bicep - a simple general purpose SAMD21G board

This is a simple ARM Cortex M0 development board with: SAMD21 cpu 2 serial connectors 915MHz Hope RFM95 Lora module LiPo battery w/usb charger and on-off switch * 3 I2C connectors (2 QWIIC and one pin header)

Bicep, from the project README
From the project README

Main components on the Bicep

Bicep bill of materials (BOM)

55 components, 39 distinct parts.

QtyPartRefs
1
ATSAMD21G18A-A
U1
1
RFM95W-915S2
U2
1
MCP73831-2
U3
1
AP2112K-3.3
U4
1
2N7002
Q1
1
DMG3401
Q2
1
32.768K-12.5p
Y1
1
DEBUG
J1
2
QWIIC
J2, J3
1
I2C
J4
1
SERIAL1
J5
1
SERIAL2
J6
1
ANALOG
J7
1
MISC
J8
1
DATA
J9
1
BATT
J10
1
USB_B_Micro
J11
1
BATT
J12
1
915Mhz
ANT1
1
RESET
SW1
Show 19 more
QtyPartRefs
1
POWER
SW2
1
LED
LED1
1
PWR
LED2
1
TX
LED3
1
RX
LED4
1
CHG
LED5
1
RGB
LED6
1
SD103CW
D1
1
1k5
FB1
2
18p
C1, C3
2
1u
C2, C4
4
100n
C5, C7, C11, C12
1
4u7
C6
4
10u
C8, C9, C10, C13
2
10K
R1, R8
2
100K
R2, R10
4
1K5
R3, R4, R5, R6
2
2K
R7, R9
2
1M
R11, R12

Bicep design files

The KiCad project lives in the albachten/bicep repository on GitHub; these links point at the commit this page was built from.

Bicep: common questions

What microcontroller does the Bicep use?

The Bicep is built around the ATSAMD21G18A-A, from the Microchip SAM family.

How big is the Bicep PCB?

The Bicep measures 70 × 85 mm, has 4 copper layers and is 1.6062 mm thick.

How many components are on the Bicep?

55 components, from 39 distinct parts. The full bill of materials is listed on this page.

Where can I download the Bicep design files?

From the albachten/bicep repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Bicep design in my own project?

Yes, under the terms of its CC0-1.0 license, which albachten chose for the repository.

Can I test firmware for the Bicep without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.

Similar boards