Linefollower
albinCuriel·LineFollower·technische tekeningen/elektronisch/kicad/linefollower.kicad_pcb
About the Linefollower PCB
Linefollower is an open source ESP32 PCB design by albinCuriel, published on GitHub. It is a 2-layer board, with 18 components from 16 distinct parts.
Its main chip is the ESP32-S3-DevKitC-1 N8R2, from the ESP32 family. Other key parts include the CN3903 3,3V, Pololu QTR-8A and TB6612FNG. By type, the board carries 4 ICs, 4 capacitors, 3 resistors, 2 modules, 2 switches and 1 connector.
From the project
Elektrisch schema van de linefollower in KiCad 10.
Elektrisch schema van de linefollower in KiCad 10.
Geen KiCad? Bekijk het schema als PDF of SVG.
ERC: 0 elektrische fouten. Er komen wel meldingen dat de standaardbibliotheken niet in deze map staan.
Main components on the Linefollower
Linefollower bill of materials (BOM)
18 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DevKitC-1 N8R2 | U1 | |
| 1 | CN3903 3,3V | U2 | |
| 1 | Pololu QTR-8A | U3 | |
| 1 | TB6612FNG | U4 | |
| 1 | GA12-N20 10:1 1500rpm enc. (links) | M1 | |
| 1 | GA12-N20 10:1 1500rpm enc. (rechts) | M2 | |
| 1 | XT30 male pigtail | J1 | |
| 1 | DOGCOM 2S 450mAh 100C | BT1 | |
| 1 | Power SS12D00 | SW1 | |
| 1 | Start/Stop | SW2 | |
| 1 | Power LED | D1 | |
| 2 | 100uF | C1, C2 | |
| 2 | 100nF | C3, C4 | |
| 1 | 10k | R1 | |
| 1 | 5,1k | R2 | |
| 1 | 330 | R3 |
Linefollower design files
The KiCad project lives in the albinCuriel/LineFollower repository on GitHub; these links point at the commit this page was built from.
Linefollower: common questions
What microcontroller does the Linefollower use?
The Linefollower is built around the ESP32-S3-DevKitC-1 N8R2, from the ESP32 family.
How big is the Linefollower PCB?
The Linefollower has 2 copper layers and is 1.6 mm thick.
How many components are on the Linefollower?
18 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Linefollower design files?
From the albinCuriel/LineFollower repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Linefollower design in my own project?
The repository has no license, so all rights stay with albinCuriel. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Linefollower without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in LineFollower
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k