Linefollower planA
albinCuriel·LineFollower·technische tekeningen/elektronisch/kicad_planA/linefollower_planA.kicad_pcb
About the Linefollower planA PCB
Linefollower planA is an open source ESP32 PCB design by albinCuriel, published on GitHub. It is a 2-layer board measuring 100 × 130 mm, with 62 components from 30 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the AP63203WU and TB6612FNG. By type, the board carries 25 resistors, 12 capacitors, 9 transistors, 5 connectors, 4 switches and 3 ICs.
From the project
Volledige linefollower op één print van 100 × 130 mm met losse SMD-onderdelen, zonder breakoutmodules. Zelfde pinverdeling als plan B (board.h), dus dezelfde firmware.

Main components on the Linefollower planA
Linefollower planA bill of materials (BOM)
62 components, 30 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N16R8 | ESP32-S3-WROOM-1 | U1 |
| 1 | AP63203WU | TSOT-23-6 | U2 |
| 1 | TB6612FNG | SSOP-24_5.3x8.2mm_P0.65mm | U3 |
| 8 | QRE1113GR | OnSemi_CASE100CY | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 |
| 1 | AO3400A | SOT-23 | Q9 |
| 1 | XT30 LiPo 2S | AMASS_XT30PW-M_1x02_P2.50mm_Horizontal | J1 |
| 1 | motor L (N20 + encoder) | JST_ZH_B6B-ZR_1x06_P1.50mm_Vertical | J2 |
| 1 | motor R (N20 + encoder) | JST_ZH_B6B-ZR_1x06_P1.50mm_Vertical | J3 |
| 1 | USB-C | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J4 |
| 1 | UART debug | PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | aan/uit | SW_SPDT_PCM12 | SW1 |
| 1 | START/STOP | SW_SPST_TL3342 | SW2 |
| 1 | BOOT | SW_SPST_TL3342 | SW3 |
| 1 | RESET | SW_SPST_TL3342 | SW4 |
| 1 | B5819W | D_SOD-123 | D1 |
| 1 | power (groen) | LED_0805_2012Metric | D2 |
| 1 | WS2812B status | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D3 |
| 1 | 6.8uH | L_Bourns-SRN4018 | L1 |
| 2 | 10uF 25V | C_1206_3216Metric | C1, C10 |
| 6 | 100nF | C_0805_2012Metric | C2, C5, C7, C9, C11, C12 |
Show 10 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 22uF | C_1206_3216Metric | C3, C4 |
| 1 | 10uF | C_0805_2012Metric | C6 |
| 1 | 1uF | C_0805_2012Metric | C8 |
| 3 | 10k | R_0805_2012Metric | R1, R4, R5 |
| 3 | 5k1 | R_0805_2012Metric | R2, R20, R21 |
| 1 | 1k | R_0805_2012Metric | R3 |
| 1 | 100 | R_0805_2012Metric | R6 |
| 1 | 100k | R_0805_2012Metric | R7 |
| 8 | 100 | R_0603_1608Metric | R10, R11, R12, R13, R14, R15, R16, R17 |
| 8 | 47k | R_0603_1608Metric | R22, R23, R24, R25, R26, R27, R28, R29 |
Linefollower planA design files
The KiCad project lives in the albinCuriel/LineFollower repository on GitHub; these links point at the commit this page was built from.
Linefollower planA: common questions
What microcontroller does the Linefollower planA use?
The Linefollower planA is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.
How big is the Linefollower planA PCB?
The Linefollower planA measures 100 × 130 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Linefollower planA?
62 components, from 30 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Linefollower planA design files?
From the albinCuriel/LineFollower repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Linefollower planA design in my own project?
The repository has no license, so all rights stay with albinCuriel. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Linefollower planA without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in LineFollower
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k