V11
alperbasarn·QNOB·V11/V11.kicad_pcb
About the V11 PCB
V11 is an open source ESP32 PCB design by alperbasarn, published on GitHub. It is a 2-layer board measuring 47.9 × 47.4 mm, with 27 components from 12 distinct parts.
Its main chip is the ESP32-C3_SUPERMINI, from the ESP32 family. Other key parts include the DRV8311HRWR and MT6701QT. By type, the board carries 10 resistors, 9 capacitors, 3 ICs, 3 connectors and 2 diodes.
From the project
HID with tactile feedback
Main components on the V11
V11 bill of materials (BOM)
27 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DRV8311HRWR ~ | IC_DRV8311HRRWR | U1 |
| 1 | ESP32-C3_SUPERMINI | MODULE_ESP32-C3_SUPERMINI | U2 |
| 1 | MT6701QT | QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm | U3 |
| 1 | Conn_01x04 | Molex_PicoBlade_53048-0410_1x04_P1.25mm_Horizontal | J1 |
| 1 | Conn_01x03 | Molex_PicoBlade_53048-0310_1x03_P1.25mm_Horizontal | J3 |
| 1 | Conn_01x05 | PinHeader_1x05_P2.54mm_Vertical | J4 |
| 2 | ESD5Zxx | D_SOD-323 | D1, D2 |
| 5 | 100N 100n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C3, C5, C7, C9 |
| 1 | 4.7U 4.7u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2 |
| 3 | 10U 10u | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C6, C8 |
| 7 | 0 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4, R5, R6, R10 |
| 3 | 4.7K 4.7k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R8, R9 |
V11 design files
The KiCad project lives in the alperbasarn/QNOB repository on GitHub; these links point at the commit this page was built from.
- LayoutV11/V11.kicad_pcb
- SchematicV11/V11.kicad_sch
- BOMV11/Fabrication/BOM.xlsx
V11: common questions
What microcontroller does the V11 use?
The V11 is built around the ESP32-C3_SUPERMINI, from the ESP32 family.
How big is the V11 PCB?
The V11 measures 47.9 × 47.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the V11?
27 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the V11 design files?
From the alperbasarn/QNOB repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the V11 design in my own project?
The repository has no license, so all rights stay with alperbasarn. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the V11 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in QNOB
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k