Openled wroom
amsterisk·openled-wroom·hardware/openled-wroom.kicad_pcb
About the Openled wroom PCB
Openled wroom is an open source ESP32 PCB design by amsterisk, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 54 × 39 mm, with 29 components from 19 distinct parts.
Its main chip is the ESP32-WROOM-32E, from the ESP32 family. Other key parts include the AMS1117-3.3 and 74AHCT125. By type, the board carries 10 resistors, 7 capacitors, 6 connectors, 3 ICs, 1 transistor and 1 switch.
It belongs with the displays & leds, usb & debug tools and iot & wireless designs in this gallery.
From the project
Open-hardware WLED controller board for the ESP32-WROOM-32E: 5 V in, four 74AHCT125-buffered WS2812B outputs. KiCad 9, CERN-OHL-S-2.0.
An open-hardware LED controller board for an ESP32-WROOM-32E module running WLED. It has 5 V in and four level-shifted WS2812B data outputs.
Status: work in progress. The schematic is done (ERC clean) and the PCB is routed (DRC clean). It has not yet been reviewed or fabricated.
- ESP32-WROOM-32E module. The antenna overhangs the top edge of the board, so there is no copper under it. - Four WS2812B outputs on GPIO16, 17, 18 and 19: - Buffered to 5 V by a 74AHCT125. Its TTL-threshold inputs are driven from 3.3 V. - A 220 Ω series resistor on each output. - A 10 kΩ pull-down on each output…
Main components on the Openled wroom
Openled wroom bill of materials (BOM)
29 components, 19 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U1 |
| 1 | ESP32-WROOM-32E | ESP32-WROOM-32E | U2 |
| 1 | 74AHCT125 | SOIC-14_3.9x8.7mm_P1.27mm | U3 |
| 1 | AO3401A | SOT-23 | Q1 |
| 1 | 5V IN | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J1 |
| 1 | LED1 | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J2 |
| 1 | LED2 | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J3 |
| 1 | LED3 | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4 |
| 1 | LED4 | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J5 |
| 1 | SERIAL | PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | BUTTON | SW_SPST_PTS645Sx43SMTR92 | SW1 |
| 1 | SMBJ5.0A | D_SMB | D1 |
| 1 | 100u 16V | CP_Elec_6.3x5.8 | C1 |
| 2 | 10u 10V | C_0805_2012Metric | C2, C4 |
| 1 | 22u 10V | C_1206_3216Metric | C3 |
| 2 | 100n | C_0603_1608Metric | C5, C7 |
| 1 | 1u | C_0603_1608Metric | C6 |
| 6 | 10k | R_0603_1608Metric | R1, R2, R3, R4, R5, R6 |
| 4 | 220 | R_0603_1608Metric | R7, R8, R9, R10 |
Openled wroom design files
The KiCad project lives in the amsterisk/openled-wroom repository on GitHub; these links point at the commit this page was built from.
Openled wroom: common questions
What microcontroller does the Openled wroom use?
The Openled wroom is built around the ESP32-WROOM-32E, from the ESP32 family.
How big is the Openled wroom PCB?
The Openled wroom measures 54 × 39 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Openled wroom?
29 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Openled wroom design files?
From the amsterisk/openled-wroom repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Openled wroom design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which amsterisk chose for the repository.
Can I test firmware for the Openled wroom without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k