41 open source boards using the MCP23017-E/SO
Real designs built with the MCP23017-E/SO, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
ClimateSprinklerController
kbx81
217 × 108 mm189 parts2LNo license55AVR/Arduino
Oscillator Board
Bad-Dog-Designs
229 × 96 mm132 parts2LNo license18Eve pi
vishhvaan
103.5 × 90.6 mm102 parts4LMIT15ESP32
Access controller
physiii150 × 90 mm186 parts4LNo license13Maxx rj45-controller
Pekaway
55.5 × 30 mm29 parts2LNo license5ESP32
Tubender
smvumbaco
352.3 × 159.3 mm252 parts4LNo license2Daughterboard
BoomBoxRobotics
155 × 80.6 mm118 parts4LCC0-1.02SwimMeet Commander
sammdu
152.4 × 76.2 mm37 parts2LNo license2Encoder i2c
samjkent
203.2 × 40.6 mm142 parts2LNo license1AVR/Arduino
EngineDataLogger-FrontControls
techie66
95 × 95 mm130 parts2LGPL-2.01ESP32
BeeFASYER SPARROW
beewarden
64.1 × 72.8 mm121 parts4LCERN-OHL-S-2.01PVDX-ADCS-PMB
BrownSpaceEngineering
82.5 × 82.5 mm106 parts4LNo license1ESP32
Audio mixer
21bsirota
173.5 × 187.5 mm788 parts4LNo license0Cm5-guard-A
Brico-Hams
290 × 280 mm157 parts2LNo license0Cm5-guard-A
anatolbricoham
290 × 280 mm157 parts2LNo license0RP2040/RP2350
Lights out-Matrix
Charles-D-FPU
87 × 137.5 mm111 parts2LNo license0Mage
mosswg
144.8 × 143.8 mm79 parts2LMIT0ESP32
Nanovolt divider
kuvychko
60 × 69.1 mm64 parts2LMIT0RP2040/RP2350
Uart cable tester
Mykola2
135 × 90 mm62 parts2LNo license0Rfid module
KyGuy2002
80 × 22 mm35 parts2LNo license0T41-exciter filter board
DRWJSCHMIDT
100 × 100 mm210 parts2LNo license64AVR/Arduino
Routing Board
Bad-Dog-Designs
229 × 96 mm131 parts2LNo license18ESP8266
App boy
zyyan20h
74.5 × 33 mm32 parts2LNo license4Daughterboard.pre r14 csd18502 swap
BoomBoxRobotics
155 × 80.6 mm118 parts4LCC0-1.02Placed prerouted
Brico-Hams
290 × 280 mm157 parts2LNo license0Placed prerouted
anatolbricoham
290 × 280 mm157 parts2LNo license0Vik playground
sadekbaroudi
99 × 65.5 mm40 parts2LCERN-OHL-P-2.0220AVR/Arduino
Commons Board
Bad-Dog-Designs
229 × 96 mm95 parts2LNo license18Daughterboard.pre r13 topology backup
BoomBoxRobotics
155 × 80.6 mm113 parts4LCC0-1.02ESP32
PortableSatCarrier
Brico-Hams
180 × 130 mm40 parts2LNo license0ESP32
PortableSatCarrier
anatolbricoham
180 × 130 mm40 parts2LNo license0T41-RF-board-V012.8
DRWJSCHMIDT
100 × 100 mm164 parts4LNo license64Daughterboard before 4layer trace wipe
BoomBoxRobotics
155 × 80.6 mm105 parts2LCC0-1.02Daughterboard before u1 pin23 neckdown
BoomBoxRobotics
155 × 80.6 mm105 parts2LCC0-1.02Daughterboard before 3v3 logic branch
BoomBoxRobotics
155 × 80.6 mm104 parts2LCC0-1.02Daughterboard before add j30 5v uart pad
BoomBoxRobotics
155 × 80.6 mm104 parts2LCC0-1.02
How designs wire the MCP23017-E/SO
Read from the KiCad layouts of 23 open source designs, one per repository: what each pin of the MCP23017-E/SO connects to, and the resistors, capacitors and other passives placed on it.
- The SCK pin has a pull-up to 3.3V on 19 of 23 designs, most often 4.7 kΩ (then 10 kΩ).
- The SDA pin has a pull-up to 3.3V on 19 of 23 designs, most often 4.7 kΩ (then 10 kΩ).
- The INTB pin is left unconnected on 18 of 23 designs (a signal on 5).
- The A0 pin is tied to GND on 17 of 23 designs (a signal on 6).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GPB1pin 2 | Connected to: Signal 87% |
|
| GPB4pin 5 | Connected to: Signal 87% |
|
| VDDpin 9 | Connected to: 3.3V 87% |
|
| VSSpin 10 | Connected to: GND 100% | — |
| NCpin 11, 14 | Connected to: Not connected 95% | — |
| SCKpin 12 | Connected to: A connector 48%, the microcontroller 30% |
|
| SDApin 13 | Connected to: A connector 48%, the microcontroller 30% |
|
| A0pin 15 | Connected to: GND 74% · a signal 26% | — |
| A1pin 16 | Connected to: GND 70% · a signal 26% | — |
| A2pin 17 | Connected to: GND 70% · a signal 26% | — |
| RESETpin 18 | Connected to: Signal 70% · 3.3V 30% |
|
| INTBpin 19 | Connected to: Not connected 78% · a signal 22% | — |
| INTApin 20 | Connected to: Not connected 65% · a signal 35% | — |
| GPA4pin 25 | Connected to: A connector 26% · not connected 17% |
|
13 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Vik playground by sadekbaroudi, T41-exciter filter board by DRWJSCHMIDT, ClimateSprinklerController by kbx81 and Commons Board by Bad-Dog-Designs.
The MCP23017-E/SO in open source designs
The gallery holds 41 open source boards using the MCP23017-E/SO from 23 GitHub repositories; a typical one measures about 155 × 82.5 mm and carries around 105 components.
76% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is Vik playground by sadekbaroudi.
Parts used alongside the MCP23017-E/SO
Microcontrollers on boards using the MCP23017-E/SO
What boards using the MCP23017-E/SO are built for
MCP23017-E/SO: common questions
Where can I find a MCP23017-E/SO reference design?
Each of the 41 boards on this page is a real design using the MCP23017-E/SO. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the MCP23017-E/SO SCK pin?
The SCK pin has a pull-up to 3.3V on 19 of 23 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 23 open source designs using the MCP23017-E/SO.
What pull-up resistor is used on the MCP23017-E/SO SDA pin?
The SDA pin has a pull-up to 3.3V on 19 of 23 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 23 open source designs using the MCP23017-E/SO.
How is the MCP23017-E/SO INTB pin connected?
The INTB pin is left unconnected on 18 of 23 designs (a signal on 5). Counted from the KiCad layouts of 23 open source designs using the MCP23017-E/SO.
What parts are used alongside the MCP23017-E/SO?
The AMS1117-3.3, AP2112K-3.3TRG1, LTV-817S, SN74HC08DR and SN74HC123DR appear in the most repositories here.
Which microcontrollers do boards using the MCP23017-E/SO use?
Most are built on ESP32 (8), AVR/Arduino (4), RP2040/RP2350 (2) and ESP8266 (1).
How big is a typical board using the MCP23017-E/SO?
The median is 155 × 82.5 mm, and 76% are two-layer designs.
What is the most popular open source board using the MCP23017-E/SO?
By GitHub stars, Vik playground by sadekbaroudi, with 220 stars.
Can I simulate one of these boards using the MCP23017-E/SO before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.