Starbie
AP-123456789·Starbie·Hardware/startbie.kicad_pcb
About the Starbie PCB
Starbie is an open source ESP32 PCB design by AP-123456789, published on GitHub. It is a 2-layer board measuring 76.5 × 71 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches and 1 resistor.
It belongs with the iot & wireless, sensors and displays & leds designs in this gallery.
From the project
Starbie is a custom embedded electronics project built around the Seeed Studio XIAO ESP32-C3 (RISC-V). It combines a Seeed XIAO ESP32-C3, a DHT11 temperature and humidity sensor, an MPU6050 IMU, a 0.96-inch I2C OLED display, and two push buttons on a custom two-layer PCB designed
Starbie is a custom embedded electronics project built around the Seeed Studio XIAO ESP32-C3 (RISC-V). It combines a Seeed XIAO ESP32-C3, a DHT11 temperature and humidity sensor, an MPU6050 IMU, a 0.96-inch I2C OLED display, and two push buttons on a custom two-layer PCB designed from scratch in KiCad.
Microcontroller: Seeed Studio XIAO ESP32-C3 (RISC-V 32-bit RISC-V single-core CPU, Wi-Fi, BLE) Display: 0.96-inch I2C Monochrome OLED Display (128x64 resolution, SSD1306 driver) Temperature/Humidity Sensor: DHT11 Sensor with a $10\text{ k}\Omega$ pull-up resistor on the data line Motion…

Main components on the Starbie
Starbie bill of materials (BOM)
7 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U1 |
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-SMD | U2 |
| 1 | Conn_01x04 | Display_128x64_096_I2C | J1 |
| 1 | Conn_01x08 | MPU6050_Module | J2 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | 10k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
Starbie design files
The KiCad project lives in the AP-123456789/Starbie repository on GitHub; these links point at the commit this page was built from.
- LayoutHardware/startbie.kicad_pcb
- SchematicHardware/startbie.kicad_sch
- BOMBOM.csv
Starbie: common questions
What microcontroller does the Starbie use?
The Starbie is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Starbie PCB?
The Starbie measures 76.5 × 71 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Starbie?
7 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Starbie design files?
From the AP-123456789/Starbie repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Starbie design in my own project?
The repository has no license, so all rights stay with AP-123456789. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Starbie without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k