D34-tec

aquarat·cat-feeder·electronics/d34/d34-tec/d34-tec.kicad_pcb

D34-tec PCB layout, top view — open source board by aquarat

About the D34-tec PCB

D34-tec is an open source PCB design by aquarat, published on GitHub under the Custom license license. It is a 2-layer board measuring 81 × 47 mm, with 39 components from 22 distinct parts.

Other key parts include the TL431AILPG. By type, the board carries 13 resistors, 8 connectors, 6 transistors, 4 diodes, 3 fuses and 2 relays.

From the project

A high performance cat-food-feeder.

Status: generated, ERC/DRC-checked design files. Not fabricated, not soldered, not powered, no firmware.

- Rationale, power budget, TVS analysis and open questions: kb/d34-controller.md. - Decision: D34.

Bare 2-layer boards (1.6 mm FR-4, 1 oz), fabrication only. Every part is through-hole or a plug-in module. Two upload packages per card: -pcbtrain.zip (PCB Train / Newbury Electronics, UK; recommended UK fab) and -jlcpcb-gerbers.zip (JLCPCB, much cheaper). Components: RS Components UK except one Farnell line and two module retailers; the sourced BOM, totals and fab comparison are in…

D34-tec, from the project README
From the project README

Main components on the D34-tec

TL431AILPG

D34-tec bill of materials (BOM)

39 components, 22 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TL431AILPG
onsemi
U1
3
2N3904BU
2N3904
onsemi
Q1, Q2, Q3
2
IRLZ44NPBF
IRLZ44N
Infineon
Q4, Q5
1
BC32725BU
BC327-25
onsemi
Q6
1
B3P-VH(LF)(SN)
+12 V from pwr card
J1
1
39-28-1063 (5566-06A)
DPS5005 output: 1-3 OUT+, 4-6 OUT-
J2
1
39-28-1043 (5566-04A)
TEC array 2S2P: 1 A 2 B 3 A 4 B
J3
1
B2P-VH(LF)(SN)
Hot-sink thermostats (series NC loop, 12 V / 35 mA)
J4
1
47053-1000
FAN1 12 V 4-pin PWM (NF-A12x25)
Molex
J5
1
47053-1000
FAN2 12 V blower (switched DC low side), tach
Molex
J6
1
47053-1000
FAN3 spare 12 V (switched low side: fan or external relay <= 0.4 A)
Molex
J7
1
B12B-XH-A(LF)(SN)
LINK to D34-CTRL
J9
1
BZX79-C15,133
BZX79-C15
DZ2
3
RXEF050
Littelfuse
F1, F2, F3
2
G2RL-2 DC12
K1, K2
4
1N5817RLG
1N5817
onsemi
D1, D5, D7, D8
1
EEU-FR1V221
220u 35V
Panasonic
C1
4
MF0204FTE52-1K
1k
Yageo
R1, R4, R6, R11
2
MF0204FTE52-330R
330
Yageo
R2, R13
2
MF0204FTE52-4K7
4.7k
Yageo
R3, R15
Show 2 more
QtyPartRefs
4
MF0204FTE52-47K
47k
Yageo
R5, R7, R9, R10
1
MF0204FTE52-10K
10k
Yageo
R14

D34-tec design files

The KiCad project lives in the aquarat/cat-feeder repository on GitHub; these links point at the commit this page was built from.

D34-tec: common questions

How big is the D34-tec PCB?

The D34-tec measures 81 × 47 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the D34-tec?

39 components, from 22 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the D34-tec design files?

From the aquarat/cat-feeder repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the D34-tec design in my own project?

It is published under Custom license, which limits how it may be reused; read the license before building on it.

More boards in cat-feeder