Feeder
aquarat·cat-feeder·electronics/pcb/feeder.kicad_pcb
About the Feeder PCB
Feeder is an open source ESP32 PCB design by aquarat, published on GitHub under the Custom license license. It is a 2-layer board measuring 58.1 × 80 mm, with 54 components from 28 distinct parts.
Its main chip is the ESP32-WROOM-32E-N4, from the ESP32 family. Other key parts include the AP2112K-3.3TRG1 and SN74LVC1G125DBVR. By type, the board carries 21 resistors, 17 connectors, 11 capacitors, 4 ICs and 1 transistor.
From the project
A high performance cat-food-feeder.
Editable KiCad 9 schematic and fully connected, two-layer shallow crescent PCB, 58.12 × 80 mm bounding box. Actual area is only 2.17% above the 50 × 80 mm rectangular baseline. This is a checked design draft, not a fabricated/tested controller. Start with packaging assumptions/comparison, design rationale and check results.
D25 HOLD: review corrections are ready for focused independent recheck; supplier-project creation remains prohibited. Precise B1/B2/rule-fix record. Current revision adds R20/R21; all original placements and the outline are preserved.

Main components on the Feeder
Feeder bill of materials (BOM)
54 components, 28 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32E-N4 | ESP32-WROOM-32E | U1 |
| 1 | AP2112K-3.3TRG1 | SOT-23-5 | U2 |
| 2 | SN74LVC1G125DBVR | SOT-23-5 | U3, U4 |
| 1 | MMBT3904 | SOT-23 | Q1 |
| 1 | C5183929 VMOT 20-24V INPUT | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J1 |
| 1 | C49257 RAILS GND-5V-12V | PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | C5116483 FAN GND-12V-TACH-PWM | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 2 | C49257 DS18B20 GND-DQ-3V3 | PinHeader_1x03_P2.54mm_Vertical | J4, J5 |
| 1 | C49257 INDEX GND-SIG-3V3 | PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | C49257 HOME GND-SIG-3V3 | PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | C5116483 I2C GND-3V3-SDA-SCL | PinHeader_1x04_P2.54mm_Vertical | J8 |
| 1 | C49257 DPS GND-RX-TX (DPS names) | PinHeader_1x03_P2.54mm_Vertical | J9 |
| 1 | C27985187 TEC ENABLE GND-ON | PinHeader_1x02_P2.54mm_Vertical | J10 |
| 1 | C5116483 PROG GND-TX-RX-3V3ref | PinHeader_1x04_P2.54mm_Vertical | J11 |
| 1 | C27985187 BOOT short for download | PinHeader_1x02_P2.54mm_Vertical | J12 |
| 1 | C27985187 RESET short to reset | PinHeader_1x02_P2.54mm_Vertical | J13 |
| 1 | C27438 A4988 CONTROL socket | PinSocket_1x08_P2.54mm_Vertical | J14 |
| 1 | C27438 A4988 POWER socket | PinSocket_1x08_P2.54mm_Vertical | J15 |
| 1 | C5183929 MOTOR COIL1 | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J16 |
| 1 | C5183929 MOTOR COIL2 | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J17 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | C15850 10u 25V | C_0805_2012Metric | C1, C2, C4, C11 |
| 5 | 100N 100n | C_0603_1608Metric | C3, C6, C7, C8, C9 |
| 1 | C15849 1u 50V | C_0603_1608Metric | C5 |
| 1 | C713402 100u 50V EEUFR1H101B | CP_Radial_D8.0mm_P5.00mm | C10 |
| 11 | 10K 10k | R_0603_1608Metric | R1, R2, R4, R5, R6, R10, R11, R14 +3 |
| 4 | 4.7K 4.7k | R_0603_1608Metric | R3, R8, R16, R17 |
| 2 | 1k | R_0603_1608Metric | R7, R15 |
| 4 | 100K 100k | R_0603_1608Metric | R9, R12, R13, R18 |
Feeder design files
The KiCad project lives in the aquarat/cat-feeder repository on GitHub; these links point at the commit this page was built from.
Feeder: common questions
What microcontroller does the Feeder use?
The Feeder is built around the ESP32-WROOM-32E-N4, from the ESP32 family.
How big is the Feeder PCB?
The Feeder measures 58.1 × 80 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Feeder?
54 components, from 28 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Feeder design files?
From the aquarat/cat-feeder repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Feeder design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
Can I test firmware for the Feeder without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in cat-feeder
ESP32
Feeder unrouted
aquarat
58.1 × 80 mm54 parts2LCustom license0ESP32
D34-ctrl
aquarat
81 × 47 mm45 parts2LCustom license0ESP32
D34-ctrl unrouted
aquarat
81 × 47 mm45 parts2LCustom license0D34-tec
aquarat
81 × 47 mm39 parts2LCustom license0D34-tec unrouted
aquarat
81 × 47 mm39 parts2LCustom license0D34-pwr
aquarat
81 × 47 mm24 parts2LCustom license0D34-pwr unrouted
aquarat
81 × 47 mm24 parts2LCustom license0Fan placement
aquarat
17.7 × 16.5 mm12 parts2LCustom license0Logic placement
aquarat
14.3 × 17.7 mm10 parts2LCustom license0
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k