Feeder unrouted

aquarat·cat-feeder·electronics/pcb/feeder-unrouted.kicad_pcb

Feeder unrouted PCB layout, top view — open source ESP32 board by aquarat

About the Feeder unrouted PCB

Feeder unrouted is an open source ESP32 PCB design by aquarat, published on GitHub under the Custom license license. It is a 2-layer board measuring 58.1 × 80 mm, with 54 components from 28 distinct parts.

Its main chip is the ESP32-WROOM-32E-N4, from the ESP32 family. Other key parts include the AP2112K-3.3TRG1 and SN74LVC1G125DBVR. By type, the board carries 21 resistors, 17 connectors, 11 capacitors, 4 ICs and 1 transistor.

From the project

A high performance cat-food-feeder.

Editable KiCad 9 schematic and fully connected, two-layer shallow crescent PCB, 58.12 × 80 mm bounding box. Actual area is only 2.17% above the 50 × 80 mm rectangular baseline. This is a checked design draft, not a fabricated/tested controller. Start with packaging assumptions/comparison, design rationale and check results.

D25 HOLD: review corrections are ready for focused independent recheck; supplier-project creation remains prohibited. Precise B1/B2/rule-fix record. Current revision adds R20/R21; all original placements and the outline are preserved.

Feeder unrouted, from the project README
From the project README

Main components on the Feeder unrouted

Feeder unrouted bill of materials (BOM)

54 components, 28 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-WROOM-32E-N4
U1
1
AP2112K-3.3TRG1
U2
2
SN74LVC1G125DBVR
U3, U4
1
MMBT3904
Q1
1
C5183929
VMOT 20-24V INPUT
J1
1
C49257
RAILS GND-5V-12V
J2
1
C5116483
FAN GND-12V-TACH-PWM
J3
2
C49257
DS18B20 GND-DQ-3V3
J4, J5
1
C49257
INDEX GND-SIG-3V3
J6
1
C49257
HOME GND-SIG-3V3
J7
1
C5116483
I2C GND-3V3-SDA-SCL
J8
1
C49257
DPS GND-RX-TX (DPS names)
J9
1
C27985187
TEC ENABLE GND-ON
J10
1
C5116483
PROG GND-TX-RX-3V3ref
J11
1
C27985187
BOOT short for download
J12
1
C27985187
RESET short to reset
J13
1
C27438
A4988 CONTROL socket
J14
1
C27438
A4988 POWER socket
J15
1
C5183929
MOTOR COIL1
J16
1
C5183929
MOTOR COIL2
J17
Show 8 more
QtyPartRefs
4
C15850
10u 25V
C1, C2, C4, C11
5
100N
100n
C3, C6, C7, C8, C9
1
C15849
1u 50V
C5
1
C713402
100u 50V EEUFR1H101B
C10
11
10K
10k
R1, R2, R4, R5, R6, R10, R11, R14 +3
4
4.7K
4.7k
R3, R8, R16, R17
2
1k
R7, R15
4
100K
100k
R9, R12, R13, R18

Feeder unrouted design files

The KiCad project lives in the aquarat/cat-feeder repository on GitHub; these links point at the commit this page was built from.

Feeder unrouted: common questions

What microcontroller does the Feeder unrouted use?

The Feeder unrouted is built around the ESP32-WROOM-32E-N4, from the ESP32 family.

How big is the Feeder unrouted PCB?

The Feeder unrouted measures 58.1 × 80 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Feeder unrouted?

54 components, from 28 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Feeder unrouted design files?

From the aquarat/cat-feeder repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Feeder unrouted design in my own project?

It is published under Custom license, which limits how it may be reused; read the license before building on it.

Can I test firmware for the Feeder unrouted without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in cat-feeder

Similar boards