D34-ctrl
aquarat·cat-feeder·electronics/d34/d34-ctrl/d34-ctrl.kicad_pcb
About the D34-ctrl PCB
D34-ctrl is an open source ESP32 PCB design by aquarat, published on GitHub under the Custom license license. It is a 2-layer board measuring 81 × 47 mm, with 45 components from 23 distinct parts.
Its main chip is the SSW-119-01-T-S, from the ESP32 family. Other key parts include the TC74HC123AP(F) and SN74HC573AN. By type, the board carries 26 resistors, 6 connectors, 6 capacitors, 4 diodes and 3 ICs.
From the project
A high performance cat-food-feeder.
Status: generated, ERC/DRC-checked design files. Not fabricated, not soldered, not powered, no firmware.
- Rationale, power budget, TVS analysis and open questions: kb/d34-controller.md. - Decision: D34.
Bare 2-layer boards (1.6 mm FR-4, 1 oz), fabrication only. Every part is through-hole or a plug-in module. Two upload packages per card: -pcbtrain.zip (PCB Train / Newbury Electronics, UK; recommended UK fab) and -jlcpcb-gerbers.zip (JLCPCB, much cheaper). Components: RS Components UK except one Farnell line and two module retailers; the sourced BOM, totals and fab comparison are in…

Main components on the D34-ctrl
D34-ctrl bill of materials (BOM)
45 components, 23 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SSW-119-01-T-S ESP32-DevKitC-32E Samtec | ESP32-DevKitC-32E_Socket | U1 |
| 1 | TC74HC123AP(F) 74HC123 | DIP-16_W7.62mm | U2 |
| 1 | SN74HC573AN 74HC573 Texas Instruments | DIP-20_W7.62mm | U3 |
| 1 | B11B-XH-A(LF)(SN) LINK to D34-PWR | JST_XH_B11B-XH-A_1x11_P2.50mm_Vertical | J1 |
| 1 | B12B-XH-A(LF)(SN) LINK to D34-TEC | JST_XH_B12B-XH-A_1x12_P2.50mm_Vertical | J2 |
| 1 | B3B-XH-A(LF)(SN) HOME sensor (DRV5023 hall, 3.3 V, open drain) | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J3 |
| 1 | B4B-XH-A(LF)(SN) LID reed + basin-full probe | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J4 |
| 1 | B5B-XH-A(LF)(SN) UI: panel LED + button | JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J6 |
| 1 | B4B-XH-A(LF)(SN) DPS5005 UART (3.3 V TTL; DPS order GND TX RX 3V3) | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J11 |
| 1 | 1N5817RLG 1N5817 onsemi | D_DO-41_SOD81_P10.16mm_Horizontal | D1 |
| 1 | 1N5817RLG 1N5817 onsemi | D_DO-41_SOD81_P2.54mm_Vertical_AnodeUp | D2 |
| 1 | HLMP-1503 STATUS Broadcom | LED_D3.0mm | D3 |
| 1 | BAT42 STMicroelectronics | D_DO-35_SOD27_P2.54mm_Vertical_AnodeUp | D9 |
| 2 | 50YXF22M5X11 22u 50V Rubycon | CP_Radial_D5.0mm_P2.00mm | C1, C2 |
| 2 | RDER71H105K2P1H03B 1u Murata | C_Rect_L5.5mm_W3.2mm_P2.50mm | C4, C5 |
| 2 | RDER71H104K0P1H03B 100n Murata | C_Rect_L4.0mm_W2.5mm_P2.50mm | C6, C7 |
| 1 | MBA02040C4703FRP00 470k Vishay | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
| 9 | MF0204FTE52-10K 10k Yageo | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R2, R4, R7, R15, R17, R20, R23, R24 +1 |
| 3 | MF0204FTE52-47K 47k Yageo | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R3, R12, R19 |
| 10 | MF0204FTE52-1K 1k Yageo | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R5, R6, R8, R10, R11, R14, R16, R18 +2 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MF0204FTE52-4K7 4.7k Yageo | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R9 |
| 1 | MF0204FTE52-330R 330 Yageo | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R13 |
| 1 | MBA02040C4703FRP00 470k Vishay | R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R26 |
D34-ctrl design files
The KiCad project lives in the aquarat/cat-feeder repository on GitHub; these links point at the commit this page was built from.
D34-ctrl: common questions
What microcontroller does the D34-ctrl use?
The D34-ctrl is built around the SSW-119-01-T-S, from the ESP32 family.
How big is the D34-ctrl PCB?
The D34-ctrl measures 81 × 47 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the D34-ctrl?
45 components, from 23 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the D34-ctrl design files?
From the aquarat/cat-feeder repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the D34-ctrl design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
Can I test firmware for the D34-ctrl without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in cat-feeder
ESP32
Feeder
aquarat
58.1 × 80 mm54 parts2LCustom license0ESP32
Feeder unrouted
aquarat
58.1 × 80 mm54 parts2LCustom license0ESP32
D34-ctrl unrouted
aquarat
81 × 47 mm45 parts2LCustom license0D34-tec
aquarat
81 × 47 mm39 parts2LCustom license0D34-tec unrouted
aquarat
81 × 47 mm39 parts2LCustom license0D34-pwr
aquarat
81 × 47 mm24 parts2LCustom license0D34-pwr unrouted
aquarat
81 × 47 mm24 parts2LCustom license0Fan placement
aquarat
17.7 × 16.5 mm12 parts2LCustom license0Logic placement
aquarat
14.3 × 17.7 mm10 parts2LCustom license0
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k