D34-ctrl unrouted

aquarat·cat-feeder·electronics/d34/d34-ctrl/d34-ctrl-unrouted.kicad_pcb

D34-ctrl unrouted PCB layout, top view — open source ESP32 board by aquarat

About the D34-ctrl unrouted PCB

D34-ctrl unrouted is an open source ESP32 PCB design by aquarat, published on GitHub under the Custom license license. It is a 2-layer board measuring 81 × 47 mm, with 45 components from 23 distinct parts.

Its main chip is the SSW-119-01-T-S, from the ESP32 family. Other key parts include the 74HC123 and SN74HC573AN. By type, the board carries 26 resistors, 6 connectors, 6 capacitors, 4 diodes and 3 ICs.

From the project

A high performance cat-food-feeder.

Status: generated, ERC/DRC-checked design files. Not fabricated, not soldered, not powered, no firmware.

- Rationale, power budget, TVS analysis and open questions: kb/d34-controller.md. - Decision: D34.

Bare 2-layer boards (1.6 mm FR-4, 1 oz), fabrication only. Every part is through-hole or a plug-in module. Two upload packages per card: -pcbtrain.zip (PCB Train / Newbury Electronics, UK; recommended UK fab) and -jlcpcb-gerbers.zip (JLCPCB, much cheaper). Components: RS Components UK except one Farnell line and two module retailers; the sourced BOM, totals and fab comparison are in…

D34-ctrl unrouted, from the project README
From the project README

Main components on the D34-ctrl unrouted

SSW-119-01-T-S74HC123SN74HC573AN

D34-ctrl unrouted bill of materials (BOM)

45 components, 23 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
SSW-119-01-T-S
ESP32-DevKitC-32E
Samtec
U1
1
74HC123
U2
1
SN74HC573AN
74HC573
Texas Instruments
U3
1
LINK to D34-PWR
J1
1
LINK to D34-TEC
J2
1
HOME sensor (DRV5023 hall, 3.3 V, open drain)
J3
1
LID reed + basin-full probe
J4
1
UI: panel LED + button
J6
1
DPS5005 UART (3.3 V TTL; DPS order GND TX RX 3V3)
J11
1
1N5817RLG
1N5817
onsemi
D1
1
1N5817RLG
1N5817
onsemi
D2
1
HLMP-1503
STATUS
Broadcom
D3
1
BAT42
STMicroelectronics
D9
2
50YXF22M5X11
22u 50V
Rubycon
C1, C2
2
RDER71H105K2P1H03B
1u
Murata
C4, C5
2
RDER71H104K0P1H03B
100n
Murata
C6, C7
1
MBA02040C4703FRP00
470k
Vishay
R1
9
MF0204FTE52-10K
10k
Yageo
R2, R4, R7, R15, R17, R20, R23, R24 +1
3
MF0204FTE52-47K
47k
Yageo
R3, R12, R19
10
MF0204FTE52-1K
1k
Yageo
R5, R6, R8, R10, R11, R14, R16, R18 +2
Show 3 more
QtyPartRefs
1
MF0204FTE52-4K7
4.7k
Yageo
R9
1
MF0204FTE52-330R
330
Yageo
R13
1
MBA02040C4703FRP00
470k
Vishay
R26

D34-ctrl unrouted design files

The KiCad project lives in the aquarat/cat-feeder repository on GitHub; these links point at the commit this page was built from.

D34-ctrl unrouted: common questions

What microcontroller does the D34-ctrl unrouted use?

The D34-ctrl unrouted is built around the SSW-119-01-T-S, from the ESP32 family.

How big is the D34-ctrl unrouted PCB?

The D34-ctrl unrouted measures 81 × 47 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the D34-ctrl unrouted?

45 components, from 23 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the D34-ctrl unrouted design files?

From the aquarat/cat-feeder repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the D34-ctrl unrouted design in my own project?

It is published under Custom license, which limits how it may be reused; read the license before building on it.

Can I test firmware for the D34-ctrl unrouted without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in cat-feeder

Similar boards