Fan placement
aquarat·cat-feeder·electronics/revb/power/fan-placement.kicad_pcb
About the Fan placement PCB
Fan placement is an open source PCB design by aquarat, published on GitHub under the Custom license license. It is a 2-layer board measuring 17.7 × 16.5 mm, with 12 components from 8 distinct parts.
From the project
A high performance cat-food-feeder.
Selected: AP63203WU-7 / C780769 for 3.3 V (1 A design budget); AP63201WU-7 / C2071044 for approximately 12 V (0.5 A fan-start budget, 0.14 A normal).
Read rationale, layout constraints and qualification gaps.
- circuit.json: complete 22-component numbered-pin integration contract, MPNs, JLC codes, KiCad symbols/footprints, datasheet links. - design.py: source generator; follows the motor block's parts schema. - analysis.json, analyze.py, testpower.py: explicit assumptions and eight analytical/fault-injection tests. - stock-evidence.json, refresh-stock.py: read-only public stock snapshots…
Fan placement bill of materials (BOM)
12 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 10u 50V X7R | C_1210_3225Metric | CP11, CP12 |
| 2 | 100n 50V X7R | C_0603_1608Metric | CP13, CP14 |
| 3 | 22u 25V X5R | C_1206_3216Metric | CP15, CP16, CP17 |
| 1 | 56p 50V C0G | C_0603_1608Metric | CP18 |
| 1 | 10uH | L_Bourns_SRN6045TA | LP2 |
| 1 | 249k 1% | R_0603_1608Metric | RP1 |
| 1 | 18k 1% | R_0603_1608Metric | RP2 |
| 1 | AP63201WU-7 | TSOT-23-6 | UP2 |
Fan placement design files
The KiCad project lives in the aquarat/cat-feeder repository on GitHub; these links point at the commit this page was built from.
Fan placement: common questions
How big is the Fan placement PCB?
The Fan placement measures 17.7 × 16.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Fan placement?
12 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Fan placement design files?
From the aquarat/cat-feeder repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Fan placement design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
More boards in cat-feeder
ESP32
Feeder unrouted
aquarat
58.1 × 80 mm54 parts2LCustom license0ESP32
Feeder
aquarat
58.1 × 80 mm54 parts2LCustom license0ESP32
D34-ctrl
aquarat
81 × 47 mm45 parts2LCustom license0ESP32
D34-ctrl unrouted
aquarat
81 × 47 mm45 parts2LCustom license0D34-tec unrouted
aquarat
81 × 47 mm39 parts2LCustom license0D34-tec
aquarat
81 × 47 mm39 parts2LCustom license0D34-pwr
aquarat
81 × 47 mm24 parts2LCustom license0D34-pwr unrouted
aquarat
81 × 47 mm24 parts2LCustom license0Logic placement
aquarat
14.3 × 17.7 mm10 parts2LCustom license0