Quadcopter-Flight-Controller

Ari-Hetti·Quadcopter-Flight-Controller·Hardware/Flight Controller/Flight Controller.kicad_pcb

Quadcopter-Flight-Controller PCB layout, top view — open source STM32 board by Ari-Hetti

About the Quadcopter-Flight-Controller PCB

Quadcopter-Flight-Controller is an open source STM32 PCB design by Ari-Hetti, published on GitHub under the MIT license. It is a 2-layer board measuring 51.3 × 55.3 mm, with 119 components from 44 distinct parts.

Its main chip is the STM32F722RETx, from the STM32 family. Other key parts include the AT7456E, LMR51430, TPS63070RNMR, KLJ-9650-5Y and ICM-45686. By type, the board carries 53 capacitors, 28 resistors, 12 connectors, 8 ICs, 6 diodes and 4 inductors.

It belongs with the robotics & motion and sensors designs in this gallery.

From the project

A Small Flight Controller For a 5in FPV Quadcopter

Quadcopter-Flight-Controller, from the project README
From the project README

Main components on the Quadcopter-Flight-Controller

Quadcopter-Flight-Controller bill of materials (BOM)

119 components, 44 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
STM32F722RETx
U1
1
AT7456E
U2
1
LMR51430
U3
2
TPS63070RNMR
U4, U5
1
KLJ-9650-5Y
U6
1
ICM-45686
U8
1
BMP280
U9
1
MMBT2222A
Q1
1
27Mhz
X1
1
X322525MOB4SI
X2
1
Q13FC1350000200
X3
1
1.0-8P WT
CN1
1
1.0-6P WT
CN2
1
1.0-5P WT
CN3
1
1.0-4P WT
CN4
4
Conn_01x04_Pin
J1, J5, J6, J7
1
Conn_01x08_Pin
J2
1
Conn_01x06_Pin
J3
1
Conn_01x05_Pin
J4
1
Conn_01x03_Pin
J8
Show 24 more
QtyPartRefs
1
TF-01A
Card1
2
TS-1088-AR02016
SW1_BOOT1, SW1_RST1
1
TYPE-C 16PIN 2MD(073)
USB1
3
1N4148W
D1, D2, D3
3
LED
D4, D5, D6
3
1uH
L1, L3, L4
1
5.6uH
L2
2
2.2uF
C1, C11
6
18pF
C2, C3, C32, C33, C34, C35
18
100nF
C4, C5, C6, C9, C19, C20, C21, C36 +10
2
47uF
C7, C8
10
22uF
C10, C12, C13, C14, C15, C16, C17, C18 +2
11
10uF
C22, C23, C26, C27, C28, C29, C30, C31 +3
4
1uF
C43, C44, C45, C46
1
33
R1
12
10k
R2, R4, R6, R10, R11, R15, R17, R19 +4
1
75
R3
1
402
R5
1
39
R7
1
100k
R8
1
22k
R9
5
5.1k
R12, R13, R26, R27, R28
3
1k
R14, R16, R25
2
1.5k
R18, R24

Quadcopter-Flight-Controller design files

The KiCad project lives in the Ari-Hetti/Quadcopter-Flight-Controller repository on GitHub; these links point at the commit this page was built from.

Quadcopter-Flight-Controller: common questions

What microcontroller does the Quadcopter-Flight-Controller use?

The Quadcopter-Flight-Controller is built around the STM32F722RETx, from the STM32 family.

How big is the Quadcopter-Flight-Controller PCB?

The Quadcopter-Flight-Controller measures 51.3 × 55.3 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Quadcopter-Flight-Controller?

119 components, from 44 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Quadcopter-Flight-Controller design files?

From the Ari-Hetti/Quadcopter-Flight-Controller repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Quadcopter-Flight-Controller design in my own project?

Yes, under the terms of its MIT license, which Ari-Hetti chose for the repository.

Can I test firmware for the Quadcopter-Flight-Controller without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards