21 open source boards using the STM32F722RETX
Real designs built with the STM32F722RETX, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Simpleflightcontroller
notaroomba
40 × 46 mm79 parts2LNo license19STM32
LineFollower-Kwark
konrad1s
139.7 × 41.3 mm70 parts4LMIT11STM32
3D Printer Mainboard STM32
m47812
130 × 110 mm186 parts2LGPL-3.010STM32
BareDrones-FC-V1
jpwolfe9912
37.1 × 37.2 mm127 parts6LNo license4STM32
Goatfc bones
Torie3
30 × 26 mm54 parts4LCC-BY-NC-4.04STM32
Stm midi poc1
LispEngineer
100 × 100 mm111 parts4LCC-BY-SA-4.03ESP32
Koganeee
Sujay-Golla
66 × 71 mm92 parts4LMIT1STM32
STM32-FlightController
premvy
40 × 44.8 mm79 parts2LMIT1STM32
Calibration board
htl-stp-ecer
54.9 × 55 mm74 parts2LNo license1STM32
Autodrone V2
jpwolfe9912
54.8 × 39.2 mm141 parts6LNo license0STM32
Quadcopter-Flight-Controller
Ari-Hetti
51.3 × 55.3 mm119 parts2LMIT0STM32
Flight-Controller for rockets
epicgamer720
40 × 52.5 mm101 parts2LNo license0STM32
Boreas
darshg321
50 × 50 mm92 parts2LNo license0STM32
FlightX
Shubhkr08
40.8 × 46.2 mm85 parts2LNo license0STM32
Pathfinder
Ningheim
50 × 55 mm82 parts2LNo license0STM32
FlightWing
adirock09
40.8 × 46.2 mm82 parts2LNo license0STM32
Flighttt-Controller
juanfierro4892
52.5 × 58.1 mm79 parts2LNo license0STM32
Flight-Controller
Mithilessh2010
40 × 46 mm79 parts2LNo license0STM32
The-Flying-Charizard
sahilchess
50 × 56 mm79 parts2LNo license0STM32
Flight controller
GodOfStrategy
77.4 × 45.1 mm78 parts2LNo license0STM32
INFERNO
SparrowTheNerd
100 × 75 mm68 parts4LNo license0
How designs wire the STM32F722RETX
Read from the KiCad layouts of 21 open source designs, one per repository: what each pin of the STM32F722RETX connects to, and the resistors, capacitors and other passives placed on it.
- The VBAT pin has a decoupling capacitor on 21 of 21 designs, most often 100 nF (then 1 µF).
- The NRST pin has a capacitor to GND on 21 of 21 designs, most often 100 nF.
- The VDD pins have a decoupling capacitor on 21 of 21 designs, most often 100 nF (then 1 µF).
- The VCAP_1 pin has a capacitor to GND on 21 of 21 designs, most often 2.2 µF (then 4.7 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VBATpin 1 | Connected to: 3.3V 100% |
|
| PC13pin 2 | Connected to: Not connected 67% · a signal 33% | — |
| PC14pin 3 | Connected to: Signal 90% |
|
| PC15pin 4 | Connected to: Signal 81% · not connected 19% |
|
| PH0pin 5 | Connected to: Signal 100% |
|
| PH1pin 6 | Connected to: Signal 95% |
|
| NRSTpin 7 | Connected to: A connector 33% |
|
| PC2pin 10 | Connected to: Not connected 62% · a signal 38% | — |
| PC3pin 11 | Connected to: Not connected 71% · a signal 29% | — |
| VSSApin 12 | Connected to: GND 100% | — |
| VDDApin 13 | Connected to: Signal 67% · 3.3V 33% |
|
| VSSpin 18, 31, 47, 63 | Connected to: GND 100% | — |
| VDDpin 19, 32, 48, 64 | Connected to: 3.3V 95% |
|
| PB2pin 27 | Connected to: Not connected 62% · a signal 38% | — |
| VCAP_1pin 30 | Connected to: Signal 100% |
|
| PC8pin 39 | Connected to: A connector 33% |
|
| PC9pin 40 | Connected to: A connector 24% |
|
| PA10pin 43 | Connected to: Not connected 67% · a signal 33% | — |
| PA15pin 50 | Connected to: Not connected 67% · a signal 33% | — |
| PC10pin 51 | Connected to: Signal 95% |
|
| PC11pin 52 | Connected to: Signal 95% |
|
| PC12pin 53 | Connected to: Signal 90% |
|
| PD2pin 54 | Connected to: A connector 24% |
|
| PB4pin 56 | Connected to: Not connected 62% · a signal 38% | — |
| PB5pin 57 | Connected to: BQ25883RGER 48%, a connector 29% |
|
| PB6pin 58 | Connected to: BMP580 48%, BQ25883RGER 48%, a connector 29% |
|
| PB7pin 59 | Connected to: BMP580 48%, BQ25883RGER 48%, a connector 24% |
|
| BOOT0pin 60 | Connected to: Signal 100% |
|
30 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Simpleflightcontroller by notaroomba, LineFollower-Kwark by konrad1s, 3D Printer Mainboard STM32 by m47812 and BareDrones-FC-V1 by jpwolfe9912.
The STM32F722RETX in open source designs
The gallery holds 21 open source boards using the STM32F722RETX from 21 GitHub repositories; a typical one measures about 50 × 50 mm and carries around 82 components.
67% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.
The most starred is Simpleflightcontroller by notaroomba.
Parts used alongside the STM32F722RETX
What boards using the STM32F722RETX are built for
STM32F722RETX: common questions
Where can I find a STM32F722RETX reference design?
Each of the 21 boards on this page is a real design using the STM32F722RETX. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the STM32F722RETX VBAT pin?
The VBAT pin has a decoupling capacitor on 21 of 21 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 21 open source designs using the STM32F722RETX.
How is the STM32F722RETX NRST pin connected?
The NRST pin has a capacitor to GND on 21 of 21 designs, most often 100 nF. Counted from the KiCad layouts of 21 open source designs using the STM32F722RETX.
What decoupling capacitors do designs use on the STM32F722RETX VDD pin?
The VDD pins have a decoupling capacitor on 21 of 21 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 21 open source designs using the STM32F722RETX.
What parts are used alongside the STM32F722RETX?
The ICM-45686, LMR51430, TPS63070RNMR, BMP580 and BQ25883RGER appear in the most repositories here.
Which microcontrollers do boards using the STM32F722RETX use?
Most are built on STM32 (20) and ESP32 (1).
How big is a typical board using the STM32F722RETX?
The median is 50 × 50 mm, and 67% are two-layer designs.
What is the most popular open source board using the STM32F722RETX?
By GitHub stars, Simpleflightcontroller by notaroomba, with 19 stars.
Can I simulate one of these boards using the STM32F722RETX before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.