31 open source boards using the LMR51430

Real designs built with the LMR51430, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

31 boardsClear filters|Most starred

How designs wire the LMR51430

Read from the KiCad layouts of 31 open source designs, one per repository: what each pin of the LMR51430 connects to, and the resistors, capacitors and other passives placed on it.

  • The SW pin has a inductor on 31 of 31 designs, most often 5.6 µH (then 6.8 µH).
  • The FB pin has a resistor to GND on 31 of 31 designs, most often 22.1 kΩ (then 13.7 kΩ).
  • The SW pin has a series capacitor on 30 of 31 designs, most often 100 nF.
  • The CB pin has a series capacitor on 30 of 31 designs, most often 100 nF.
GNDpin 1Connected to: GND 100%
SWpin 2Connected to: Signal 100%
  • Inductor on 100% · 5.6 µH (8), 6.8 µH (7), 2.2 µH (2)
  • Series capacitor on 97% · 100 nF (30)
VINpin 3Connected to: VSYS 77% · a signal 23%
  • Decoupling capacitor on 94% · 2.2 µF (15), 10 µF (13), 100 nF (10)
FBpin 4Connected to: Signal 100%
  • Resistor to GND on 100% · 22.1 kΩ (17), 13.7 kΩ (9), 19.1 kΩ (1)
  • Pull-up to 3.3V on 81% · 100 kΩ (23), 162 kΩ (1), 187 kΩ (1)
ENpin 5Connected to: VSYS 74% · a signal 26%
CBpin 6Connected to: Signal 100%
  • Series capacitor on 97% · 100 nF (30)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Simpleflightcontroller by notaroomba, Nexrig by alanmimms, ControlBoard by ConfusedHello and BajieHeader by Penta0308.

The LMR51430 in open source designs

The gallery holds 31 open source boards using the LMR51430 from 31 GitHub repositories; a typical one measures about 52.5 × 55.3 mm and carries around 85 components.

52% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.

The most starred is Simpleflightcontroller by notaroomba.

Microcontrollers on boards using the LMR51430

LMR51430: common questions

Where can I find a LMR51430 reference design?

Each of the 31 boards on this page is a real design using the LMR51430. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the LMR51430 SW pin connected?

The SW pin has a inductor on 31 of 31 designs, most often 5.6 µH (then 6.8 µH). Counted from the KiCad layouts of 31 open source designs using the LMR51430.

What resistor goes on the LMR51430 FB pin?

The FB pin has a resistor to GND on 31 of 31 designs, most often 22.1 kΩ (then 13.7 kΩ). Counted from the KiCad layouts of 31 open source designs using the LMR51430.

How is the LMR51430 CB pin connected?

The CB pin has a series capacitor on 30 of 31 designs, most often 100 nF. Counted from the KiCad layouts of 31 open source designs using the LMR51430.

What parts are used alongside the LMR51430?

The ICM-45686, TPS63070RNMR, BMP580, BQ25883RGER and STM32F722RETX appear in the most repositories here.

Which microcontrollers do boards using the LMR51430 use?

Most are built on STM32 (23), RP2040/RP2350 (4) and ESP32 (1).

How big is a typical board using the LMR51430?

The median is 52.5 × 55.3 mm, and 52% are two-layer designs.

What is the most popular open source board using the LMR51430?

By GitHub stars, Simpleflightcontroller by notaroomba, with 19 stars.

Can I simulate one of these boards using the LMR51430 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part