Navigator

azure-dynamics·navigator·hardware/navigator.kicad_pcb

Navigator PCB layout, top view — open source ESP32 board by azure-dynamics

About the Navigator PCB

Navigator is an open source ESP32 PCB design by azure-dynamics, published on GitHub under the CERN-OHL-S-2.0 license. It is a 4-layer board measuring 65 × 56.5 mm, with 49 components from 23 distinct parts.

Its main chip is the ESP32-S3-MINI-1U, from the ESP32 family. Other key parts include the AP2112K-3.3, MPM3550EGLE, BNO086 and INA226. By type, the board carries 17 resistors, 13 capacitors, 10 connectors, 5 ICs, 2 switches and 2 diodes.

It belongs with the sensors and robotics & motion designs in this gallery.

From the project

Flight-controller Pi HAT for Azure Dynamics' Radiance ROV

Flight-controller Pi HAT for Azure Dynamics' Radiance ROV

Navigator is a Raspberry Pi HAT designed to host the low-level flight controller for the Radiance ROV. It manages communication between the Raspberry Pi and the ROV's hardware, monitoring system power and routing control signals.

Flight Control: Powered by an ESP32-S3 processor. Power Management: On-board voltage regulation supplying power directly to the Raspberry Pi and HAT logic. Propulsion Signals: Six dedicated ESC signal outputs for motor control. Sensor Integration: Includes battery voltage monitoring and I2C expansion support…

Main components on the Navigator

Navigator bill of materials (BOM)

49 components, 23 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
AP2112K-3.3
U1
1
MPM3550EGLE
U2
1
BNO086
U3
1
ESP32-S3-MINI-1U
U4
1
INA226
U5
6
BLDC-1
J1, J2, J3, J4, J5, J6
1
CONN_01X02_PIN
Conn_01x02_Pin
J7
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J8
1
CONN_01X04_PIN
Conn_01x04_Pin
J9
1
GPIO
J10
2
SW_SPST
SW1, SW2
2
D_Schottky
D1, D2
1
100UF
100uF
C1
1
10UF
10uF
C2
2
10UF
10uF
C3, C6
2
1UF
1uF
C4, C12
1
47UF
47uF
C5
6
0.1UF
0.1uF
C7, C8, C9, C10, C11, C13
11
10K
10k
R1, R2, R3, R4, R5, R6, R9, R14 +3
1
100K
100k
R7
Show 3 more
QtyPartRefs
1
14K3
14k3
R8
2
5K1
5k1
R10, R11
2
2K2
2k2
R12, R13

Navigator design files

The KiCad project lives in the azure-dynamics/navigator repository on GitHub; these links point at the commit this page was built from.

Navigator: common questions

What microcontroller does the Navigator use?

The Navigator is built around the ESP32-S3-MINI-1U, from the ESP32 family.

How big is the Navigator PCB?

The Navigator measures 65 × 56.5 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Navigator?

49 components, from 23 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Navigator design files?

From the azure-dynamics/navigator repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Navigator design in my own project?

Yes, under the terms of its CERN-OHL-S-2.0 license, which azure-dynamics chose for the repository.

Can I test firmware for the Navigator without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards