Wrist boy
benjaminbardossy-dotcom·wrist-boy·PCB/pip_boy_V1.kicad_pcb
About the Wrist boy PCB
Wrist boy is an open source ESP32 PCB design by benjaminbardossy-dotcom, published on GitHub under the MIT license. It is a 4-layer board measuring 106.4 × 66.8 mm, with 35 components from 21 distinct parts.
Its main chip is the ESP32, from the ESP32 family. Other key parts include the SSD1309, MAX30102, AHT20+BMP280, 5 way switch and INMP441. By type, the board carries 11 resistors, 9 ICs, 6 switches, 5 diodes, 1 buzzer and 1 inductor.
It belongs with the sensors, audio and power & battery designs in this gallery.
From the project
A small WIP device which takes in external information through a variety of sensors, which can be mounted to your wrist for easy access.
Despite similar ideas, I had envisioned a few changes to the design, including adding more "survival" based modules. I wanted this device to warn the user if there was any potential danger. To implement this, I added an SpO2 module to measure the users heartrate, an AHT20+BMP280 module for temp and air pressure, an MQ135 module for air quality, and a red LED which would flash if there was any potential danger to the user(E.x. low air quality readings from the MQ135, high temp readings from the AHT20+BMP280.).
Main components on the Wrist boy
Wrist boy bill of materials (BOM)
35 components, 21 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32 | ESP32_elegoo | U1 |
| 1 | SSD1309 | SSD1309(4_pin) | U3 |
| 1 | MAX30102 | PinSocket_2x04_P2.54mm_Vertical | U4 |
| 1 | AHT20+BMP280 | PinSocket_1x04_P2.54mm_Vertical | U5 |
| 1 | 5 way switch | 5_way_switch | U6 |
| 1 | INMP441 | INMP441 | U8 |
| 1 | MAX98357A | MAX98357A | U10 |
| 1 | TP4056 | TP4056_module | U12 |
| 1 | Boost Converter | mini_step-up_boost_converter | U13 |
| 1 | Buzzer | Piezo_buzzer_D10mm | BZ1 |
| 1 | MQ135 | PinSocket_1x04_P2.54mm_Vertical | MQ135 |
| 1 | Speaker | 8Ohm_1W_20mm_speaker | S1 |
| 3 | SW_SPDT | PinSocket_1x03_P2.54mm_Vertical | SW1, SW2, SW3 |
| 2 | SW_Push | SW_PUSH_6mm_H4.3mm | SW4, SW5 |
| 1 | VL53L0X | PinSocket_1x06_P2.54mm_Vertical | VL53L0X |
| 5 | LED | PinSocket_2x01_P2.54mm_Vertical | D1, D2, D3, D4, D5 |
| 1 | LASER | PinSocket_2x01_P2.00mm_Vertical | L1 |
| 6 | 10 | Resistor_THT_L5.00mm_D1.0mm | R1, R2, R3, R4, R5, R6 |
| 2 | 100K | Resistor_THT_L5.00mm_D1.0mm | R7, R8 |
| 1 | 180 | Resistor_THT_L5.00mm_D1.0mm | R9 |
Show 1 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 4.7K | Resistor_THT_L5.00mm_D1.0mm | R10, R11 |
Wrist boy design files
The KiCad project lives in the benjaminbardossy-dotcom/wrist-boy repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/pip_boy_V1.kicad_pcb
- SchematicPCB/pip_boy_V1.kicad_sch
Wrist boy: common questions
What microcontroller does the Wrist boy use?
The Wrist boy is built around the ESP32, from the ESP32 family.
How big is the Wrist boy PCB?
The Wrist boy measures 106.4 × 66.8 mm, has 4 copper layers and is 1.600198 mm thick.
How many components are on the Wrist boy?
35 components, from 21 distinct parts. The full bill of materials is listed on this page.
Where can I download the Wrist boy design files?
From the benjaminbardossy-dotcom/wrist-boy repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Wrist boy design in my own project?
Yes, under the terms of its MIT license, which benjaminbardossy-dotcom chose for the repository.
Can I test firmware for the Wrist boy without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k