L103-drv8313-as5600

bjthemost-hub·l103-drv8313-as5600·hardware/L103_CANUSB_DRV8313.kicad_pcb

L103-drv8313-as5600 PCB layout, top view — open source WCH CH32/CH55x board by bjthemost-hub

About the L103-drv8313-as5600 PCB

L103-drv8313-as5600 is an open source WCH CH32/CH55x PCB design by bjthemost-hub, published on GitHub under the MIT license. It is a 2-layer board measuring 49.2 × 49.2 mm, with 68 components from 43 distinct parts.

Its main chip is the CH32L103K8U6, from the WCH CH32/CH55x family. Other key parts include the LMR16006XDDCR, SN65HVD230, AS5600, DRV8313PWP and INA240A2PW. By type, the board carries 25 capacitors, 19 resistors, 7 ICs, 6 diodes, 3 test points and 3 inductors.

It belongs with the robotics & motion designs in this gallery.

From the project

Joint motor driver: CH32L103 + DRV8313 + AS5600. KiCad hardware, FOC firmware, PC tools, 2-stage planetary gearbox (J, 25:1). MIT.

CH32L103 主控 + DRV8313 三相驱动 + AS5600 磁编码器的关节电机驱动板,跑 FOC 的固件、 调参用的上位机,以及配套的两级行星减速机(J 版,25:1)。

上位机是独立仓库:l103-servo-gui(同一套 GUI 也支持 DRV8316C 板)。

设计值(出处:firmware/User/board.h 顶部的网表核对注释,2026-09-18 核过一遍):

hardware/gerber/ 里是可直接下单的 Gerber。原理图导出件见 hardware/L103CANUSBDRV8313.pdf 和 hardware/docs/ 里的 PNG/SVG。

- 控制:PWM 20 kHz;开环由 3 kHz 中断推进电角度(focmotor.c DRIVEISRFREQHZ), 闭环在主循环里跑(要读编码器,不适合塞进中断)。 - 反馈:AS5600 走 I2C1,12 位原始角,固件里做多圈累加与速度估计。 - 参数:极对数 / 堵转阈值 / 母线电压等存在 Flash 配置页,上电读回;读不到就用编译默认值。 默认电机 HT4310、14 极对(board.h MOTORPOLEPAIRS)。 - 通信:CAN 1 Mbps(节点 1–63)或串口 115200,两套命令等价。完整命令表见…

L103-drv8313-as5600, from the project README
From the project README

Main components on the L103-drv8313-as5600

L103-drv8313-as5600 bill of materials (BOM)

68 components, 43 distinct parts.

QtyPartRefs
1
LMR16006XDDCR
TI(德州仪器)
U2
1
CH32L103K8U6
U3
1
SN65HVD230
U4
1
AS5600
U5
1
DRV8313PWP
U6
2
INA240A2PW
U8, U10
1
Si2319CDS
Q1
1
1.27
J1
1
XT30PW(2+2)-M.G.B
XT30PW(2+2)-M
AMASS(艾迈斯)
J2
1
SMD1812P300SLR/24/3A
F1
1
10K
RV1
1
MOT_U
TP28
1
V
TP29
1
W
TP30
1
LED绿
D1
1
LED红
D2
1
SS16
D3
1
LED_RED
D4
1
BZT52C10-TP
D5
1
SMBJ28A
D6
Show 23 more
QtyPartRefs
1
600R
FB2
1
600R
FB3
1
ANR4030T470M
APV(爱普微)
L2
4
100n
C2, C13, C15, C28
3
10uF
C3, C11, C12
1
22uF35v
C4
1
47uF/35V
C5
1
47uF/100V
C6
1
0.47uF
C10
1
22uF/35v
C14
9
100nF
C16, C17, C18, C19, C21, C22, C23, C25 +1
1
1Uf
C20
1
10uF/63V
C24
2
22uF/10V
C26, C27
3
4.7k
R1, R3, R4
5
10k
R2, R5, R6, R7, R25
2
100K
R9, R15
1
30K1
R10
1
22K
R11
1
120R
R12
2
22
R14, R16
2
860
R17, R21
2
10mR
R19, R20

L103-drv8313-as5600 design files

The KiCad project lives in the bjthemost-hub/l103-drv8313-as5600 repository on GitHub; these links point at the commit this page was built from.

L103-drv8313-as5600: common questions

What microcontroller does the L103-drv8313-as5600 use?

The L103-drv8313-as5600 is built around the CH32L103K8U6, from the WCH CH32/CH55x family.

How big is the L103-drv8313-as5600 PCB?

The L103-drv8313-as5600 measures 49.2 × 49.2 mm, has 2 copper layers and is 1.60004 mm thick.

How many components are on the L103-drv8313-as5600?

68 components, from 43 distinct parts. The full bill of materials is listed on this page.

Where can I download the L103-drv8313-as5600 design files?

From the bjthemost-hub/l103-drv8313-as5600 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the L103-drv8313-as5600 design in my own project?

Yes, under the terms of its MIT license, which bjthemost-hub chose for the repository.

Can I test firmware for the L103-drv8313-as5600 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug WCH CH32/CH55x firmware against it before you order a PCB.

Similar boards