10 open source boards using the INA240A2PW
Real designs built with the INA240A2PW, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Battery
86kkd
56.6 × 33.7 mm139 parts6LNo license0STM32
TorqController
JoaoWMHentz
58.5 × 43.1 mm129 parts2LNo license0STM32
FOC
IpinZhu
50 × 70 mm112 parts4LMIT0WCH CH32/CH55x
L103-drv8313-as5600
bjthemost-hub
49.2 × 49.2 mm68 parts2LMIT0STM32
Dual-FOC-Controller
Zhang-JK
46 × 46 mm61 parts4LNo license0Sensor
86kkd
38.6 × 43.9 mm53 parts2LNo license0MOBO DEV BreadBoard
robotique-udes
39.4 × 98.5 mm35 parts4LGPL-2.01- schematic only · 326 partsESP32
Skateboard
86kkd
326 parts2LNo license0 ESP32
EStop
robotique-udes
141 × 73.5 mm32 parts2LGPL-2.01BNO BREAKOUT
robotique-udes
42 × 61.1 mm10 parts2LGPL-2.01
How designs wire the INA240A2PW
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the INA240A2PW connects to, and the resistors, capacitors and other passives placed on it.
- The + pin has a series resistor on 4 of 6 designs, most often 10 mΩ (then 1 kΩ).
- The V+ pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 4.7 µF).
- The REF1 pin has a capacitor to GND on 2 of 5 designs, most often 100 nF (then 4.7 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 4 | Connected to: GND 64% · a signal 18% | — |
| +pin 2 | Connected to: A connector 33% · GND 17% |
|
| -pin 3 | Connected to: A connector 33% · GND 17% · 3.3V 17% |
|
| V+pin 5 | Connected to: 3.3V 80% · a signal 20% |
|
| REF1pin 7 | Connected to: GND 40% · 3.3V 40% · a signal 20% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include BNO BREAKOUT by robotique-udes, Battery by 86kkd, L103-drv8313-as5600 by bjthemost-hub and FOC by IpinZhu.
The INA240A2PW in open source designs
The gallery holds 10 open source boards using the INA240A2PW from 6 GitHub repositories; a typical one measures about 49.2 × 49.2 mm and carries around 65 components.
60% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is MOBO DEV BreadBoard by robotique-udes.
Parts used alongside the INA240A2PW
Microcontrollers on boards using the INA240A2PW
What boards using the INA240A2PW are built for
INA240A2PW: common questions
Where can I find a INA240A2PW reference design?
Each of the 10 boards on this page is a real design using the INA240A2PW. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the INA240A2PW + pin?
The + pin has a series resistor on 4 of 6 designs, most often 10 mΩ (then 1 kΩ). Counted from the KiCad layouts of 6 open source designs using the INA240A2PW.
What decoupling capacitors do designs use on the INA240A2PW V+ pin?
The V+ pin has a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 6 open source designs using the INA240A2PW.
How is the INA240A2PW REF1 pin connected?
The REF1 pin has a capacitor to GND on 2 of 5 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 6 open source designs using the INA240A2PW.
Which microcontrollers do boards using the INA240A2PW use?
Most are built on ESP32 (3), STM32 (3) and WCH CH32/CH55x (1).
How big is a typical board using the INA240A2PW?
The median is 49.2 × 49.2 mm, and 60% are two-layer designs.
What is the most popular open source board using the INA240A2PW?
By GitHub stars, MOBO DEV BreadBoard by robotique-udes, with 1 stars.
Can I simulate one of these boards using the INA240A2PW before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.