24 open source boards using the AS5600
Real designs built with the AS5600, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Ethersweep
Neumi
79 × 38 mm97 parts2LMIT587RISC-V
Euroknob
mitxela
24 × 79 mm23 parts2LNo license20RP2040/RP2350
Magnetic Encoder Board
ROAR-QUTRC
40 × 40 mm72 parts4LNo license10Nordic nRF
Revolutetestboard
tongtongwang86
54 × 85.7 mm254 parts4LCC-BY-NC-4.05ESP32
Soldered Inkplate 6 MOTION
SolderedElectronics
144.4 × 107.8 mm313 parts2LTAPR-OHL-1.04ESP32
Esp miniarm
Gray-Stone
58.5 × 50 mm49 parts2LNo license1AVR/Arduino
Logic
Keisuke063
50 × 50 mm43 parts4LNo license1ESP32
Stepper-Motor-Controller
Ricsi1231
42.3 × 42.3 mm86 parts6LMIT0WCH CH32/CH55x
L103-drv8313-as5600
bjthemost-hub
49.2 × 49.2 mm68 parts2LMIT0ESP32
Thermometer
RolandThsive
71.9 × 68.9 mm31 parts2LCC-BY-NC-4.00STM32
High res scrollwheel
Jonathan-C-L
59 × 44 mm25 parts2LNo license0- schematic only · 94 partsSTM32
Rattack v2
mij001
94 partsNo license0 - schematic only · 53 partsSTM32
JB-Micro-Wheeled leg-Robot
baijiazheng
53 partsNo license0 - schematic only · 6 partsMicrochip SAM
ConveyorClock
SiegeLord
6 partsGPL-3.00 - schematic only · 5 partsESP32
ATOM-Actuators
joshomak
5 partsMIT0 ESP32
Soldered Inkplate 6 MOTION panel
SolderedElectronics
144.4 × 221.6 mm313 parts2LTAPR-OHL-1.04AS5600
racerxdl
22.9 × 22.9 mm9 parts2LMIT6Nordic nRF
Revolute production
tongtongwang86
19.9 × 19.5 mm59 parts4LCC-BY-NC-4.05Encoder board
hacker-fab
65 × 65 mm3 parts2LCustom license1Revo joint encoder
ratmuds
22 × 22 mm10 parts2LMIT0Revo servo hat
ratmuds
22 × 27 mm10 parts2LMIT0BLDC encoder pcb(2024-11-29 155120)
Freimor
30 × 22.3 mm5 parts2LNo license0Top
tongtongwang86
9.6 × 11.6 mm5 parts4LCC-BY-NC-4.05STM32
Encoder
Tomoshibi-technology
50 × 40 mm57 parts2LMIT1
How designs wire the AS5600
Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the AS5600 connects to, and the resistors, capacitors and other passives placed on it.
- The VDD3V3 pin has a decoupling capacitor on 15 of 16 designs, most often 100 nF (then 22 µF).
- The VDD5V pin has a decoupling capacitor on 13 of 16 designs, most often 100 nF (then 1 µF).
- The SDA pin has a pull-up to 3.3V on 10 of 16 designs, most often 4.7 kΩ (then 10 kΩ).
- The SCL pin has a pull-up to 3.3V on 10 of 16 designs, most often 4.7 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDD5Vpin 1 | Connected to: 3.3V 69% · a signal 19% |
|
| VDD3V3pin 2 | Connected to: 3.3V 75% · a signal 25% |
|
| OUTpin 3 | Connected to: Not connected 69% · a signal 31% | — |
| GNDpin 4 | Connected to: GND 100% | — |
| PGOpin 5 | Connected to: Not connected 63% · a signal 25% | — |
| SDApin 6 | Connected to: The microcontroller 63%, a connector 31% |
|
| SCLpin 7 | Connected to: The microcontroller 63%, a connector 31% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ethersweep by Neumi, Euroknob by mitxela, Magnetic Encoder Board by ROAR-QUTRC and AS5600 by racerxdl.
The AS5600 in open source designs
The gallery holds 24 open source boards using the AS5600 from 20 GitHub repositories; a typical one measures about 49.6 × 43.2 mm and carries around 46 components.
70% are two-layer designs, the rest use four layers or more, and 46% carry an open source license.
The most starred is Ethersweep by Neumi.
Parts used alongside the AS5600
Microcontrollers on boards using the AS5600
What boards using the AS5600 are built for
AS5600: common questions
Where can I find a AS5600 reference design?
Each of the 24 boards on this page is a real design using the AS5600. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the AS5600 VDD3V3 pin?
The VDD3V3 pin has a decoupling capacitor on 15 of 16 designs, most often 100 nF (then 22 µF). Counted from the KiCad layouts of 16 open source designs using the AS5600.
What decoupling capacitors do designs use on the AS5600 VDD5V pin?
The VDD5V pin has a decoupling capacitor on 13 of 16 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 16 open source designs using the AS5600.
What pull-up resistor is used on the AS5600 SDA pin?
The SDA pin has a pull-up to 3.3V on 10 of 16 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 16 open source designs using the AS5600.
What parts are used alongside the AS5600?
The USBLC6-2SC6, AMS1117-3.3, CH340C, ESP32-C3-WROOM-02 and MIC5219-3.3YM5 appear in the most repositories here.
Which microcontrollers do boards using the AS5600 use?
Most are built on ESP32 (6), STM32 (5), Nordic nRF (2) and RP2040/RP2350 (1).
How big is a typical board using the AS5600?
The median is 49.6 × 43.2 mm, and 70% are two-layer designs.
What is the most popular open source board using the AS5600?
By GitHub stars, Ethersweep by Neumi, with 587 stars.
Can I simulate one of these boards using the AS5600 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.