Diplomna
bribarski7·Diplomna·electricscheme/electricscheme.kicad_pcb
About the Diplomna PCB
Diplomna is an open source ESP32 PCB design by bribarski7, published on GitHub. It is a 2-layer board measuring 121.9 × 78.7 mm, with 25 components from 12 distinct parts.
Its main chip is the ESP32-DEVKITC, from the ESP32 family. Other key parts include the LM358 and LM35. By type, the board carries 8 diodes, 8 resistors, 4 capacitors and 3 ICs.
Main components on the Diplomna
Diplomna bill of materials (BOM)
25 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM358 | DIP-8_W7.62mm_LongPads | U1 |
| 1 | ESP32-DEVKITC | MODULE_ESP32-DEVKITC | U3 |
| 1 | LM35 | SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 2 | 10k | Potentiometer_ACP_CA14-VSMD_Vertical_Hole | RV1, RV2 |
| 2 | POWER LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 2 | IR TX | LED_D5.0mm | D3, D4 |
| 2 | IR RX | LED_D5.0mm | D5, D6 |
| 2 | Detection LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D7, D8 |
| 4 | 0.1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4 |
| 4 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R7, R8 |
| 2 | 100 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R4 |
| 2 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R6 |
Diplomna design files
The KiCad project lives in the bribarski7/Diplomna repository on GitHub; these links point at the commit this page was built from.
Diplomna: common questions
What microcontroller does the Diplomna use?
The Diplomna is built around the ESP32-DEVKITC, from the ESP32 family.
How big is the Diplomna PCB?
The Diplomna measures 121.9 × 78.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Diplomna?
25 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the Diplomna design files?
From the bribarski7/Diplomna repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Diplomna design in my own project?
The repository has no license, so all rights stay with bribarski7. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Diplomna without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k