7 open source boards using the LM35
Real designs built with the LM35, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Multislope-3I
NNNILabs
100 × 74 mm124 parts4LMIT43AVR/Arduino
PQDB-Hardware
augustocrmattos
147.3 × 146.8 mm73 parts2LNo license14AVR/Arduino
Pqdb
rmaalmeida
146.1 × 141 mm70 parts2LNo license1STM32
InclinationMeter
soldernerd
90 × 70 mm114 parts4LNo license0NXP
Modulo-Lector
vecchiettidaniel
189.2 × 94 mm99 parts2LNo license0ESP32
Diplomna
bribarski7
121.9 × 78.7 mm25 parts2LNo license0Tdse tpf 1-04
luqas11
130 × 150 mm13 parts2LNo license0
How designs wire the LM35
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the LM35 connects to, and the resistors, capacitors and other passives placed on it.
- The +VS pin is tied to 5V on 63% of them (a signal on 3).
- The VOUT pin has a series resistor on 3 of 7 designs, most often 0 Ω (then 2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| +VSpin 1 | Connected to: 5V 63% · a signal 38% | — |
| VOUTpin 2 | Connected to: Signal 86% |
|
| GNDpin 3 | Connected to: GND 63% · a signal 25% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Multislope-3I by NNNILabs, PQDB-Hardware by augustocrmattos, Pqdb by rmaalmeida and Diplomna by bribarski7.
The LM35 in open source designs
The gallery holds 7 open source boards using the LM35 from 7 GitHub repositories; a typical one measures about 130 × 94 mm and carries around 73 components.
71% are two-layer designs, the rest use four layers or more, and 14% carry an open source license.
The most starred is Multislope-3I by NNNILabs.
Parts used alongside the LM35
Microcontrollers on boards using the LM35
What boards using the LM35 are built for
LM35: common questions
Where can I find a LM35 reference design?
Each of the 7 boards on this page is a real design using the LM35. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM35 +VS pin connected?
The +VS pin is tied to 5V on 63% of them (a signal on 3). Counted from the KiCad layouts of 7 open source designs using the LM35.
What resistor goes on the LM35 VOUT pin?
The VOUT pin has a series resistor on 3 of 7 designs, most often 0 Ω (then 2 kΩ). Counted from the KiCad layouts of 7 open source designs using the LM35.
What parts are used alongside the LM35?
The 74HC595, DISPLAY_JHD162A, DS1307Z and KW4-361 appear in the most repositories here.
Which microcontrollers do boards using the LM35 use?
Most are built on AVR/Arduino (2), ESP32 (1), NXP (1) and RP2040/RP2350 (1).
How big is a typical board using the LM35?
The median is 130 × 94 mm, and 71% are two-layer designs.
What is the most popular open source board using the LM35?
By GitHub stars, Multislope-3I by NNNILabs, with 43 stars.
Can I simulate one of these boards using the LM35 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.