Drill

BrnoMarsRover·Drilling·pcbs/drill_pcb_v3/drill_pcb.kicad_pcb

Drill PCB layout, top view — open source ESP32 board by BrnoMarsRover

About the Drill PCB

Drill is an open source ESP32 PCB design by BrnoMarsRover, published on GitHub. It is a 2-layer board measuring 105 × 103 mm, with 44 components from 34 distinct parts.

Its main chip is the ESP32-DevKitC, from the ESP32 family. Other key parts include the LM3940, INA219BxD, Driver_TMC5160 and Driver_TMC2208. By type, the board carries 16 connectors, 12 capacitors, 7 resistors, 3 ICs, 2 modules and 2 fuses.

From the project

Repo for Deep Sampling Sub-Task

- P-MOSFET na MainBoard 2, url: https://cz.mouser.com/ProductDetail/onsemi/FDN338P?qs=HK%252BeIG1iaag%252B6528k3ktAg%3D%3D\&srsltid=AfmBOopaRxGhuw91gWSMGtCGucpT9BQNKklBUyEe4Xwb5UvMYGCLGTto - ADC rezervní, url: https://cz.mouser.com/ProductDetail/Texas-Instruments/ADS122C04IPWR?qs=7EBvPakHacWatwmmdfjwqQ%3D%3D

Main components on the Drill

ESP32-DevKitCLM3940INA219BxDDriver_TMC5160Driver_TMC2208

Drill bill of materials (BOM)

44 components, 34 distinct parts.

QtyPartRefs
1
ESP32-DevKitC
U1
1
LM3940
U2
1
INA219BxD
U3
1
Driver_TMC5160
A1
1
Driver_TMC2208
A2
1
SI2333-TP
Q3
1
24V IN
J1
1
uC COMMUNICATION
J2
1
ENCODER VERTICAL DRIVE
J3
1
LIMIT SWITCH TOP
J4
1
HEIGHT SENSOR
J5
1
STEPPER VERTICAL DRIVE
J6
1
DC MOTOR 24 V
J7
1
DC MOTOR UART
J8
1
ENCODER STORAGE
J9
1
LIMIT SWITCH BOTTOM
J10
1
DEEP WEIGHT SENSOR
J11
1
SURFACE WEIGHT SENSOR
J12
1
SERVO ROCK
J13
1
SERVO SAND
J14
Show 14 more
QtyPartRefs
1
STEPPER STORAGE
J15
1
TEST PADS
J16
1
5A
F1
1
2A
F2
1
TBA2-0511
V1
2
33 μF
C1, C3
6
100n
C2, C4, C7, C8, C9, C13
2
100μ
C5, C12
1
1000μ
C6
1
470μ
C11
2
1k
R1, R4
2
2200
R2, R3
2
100k
R5, R6
1
R100
R7

Drill design files

The KiCad project lives in the BrnoMarsRover/Drilling repository on GitHub; these links point at the commit this page was built from.

Drill: common questions

What microcontroller does the Drill use?

The Drill is built around the ESP32-DevKitC, from the ESP32 family.

How big is the Drill PCB?

The Drill measures 105 × 103 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Drill?

44 components, from 34 distinct parts. The full bill of materials is listed on this page.

Where can I download the Drill design files?

From the BrnoMarsRover/Drilling repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Drill design in my own project?

The repository has no license, so all rights stay with BrnoMarsRover. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Drill without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in Drilling

Similar boards