Starbie
choosye·Starbie·PCB/Starbie (Half-Life).kicad_pcb
About the Starbie PCB
Starbie is an open source ESP32 PCB design by choosye, published on GitHub. It is a 2-layer board measuring 119 × 93 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches and 1 resistor.
It belongs with the displays & leds designs in this gallery.
From the project
Half Life Hack Club Week 1 - Starbie
Starbie is a beginner hardware project built around a Seeed Studio XIAO ESP32-C3. The design includes an OLED display, a motion sensor, an environmental sensor, and buttons for interaction. The project introduces PCB design, circuit schematics, and Arduino firmware.
The firmware has been compiled in the Arduino IDE, but the project has not yet been tested on a physical board. Further customisation and testing may happen as I continue learning :)
Main components on the Starbie
Starbie bill of materials (BOM)
7 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-SMD | U1 |
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U2 |
| 1 | Conn_01x04_Pin | Display_128x64_096_I2C | J1 |
| 1 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J2 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | 10k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
Starbie design files
The KiCad project lives in the choosye/Starbie repository on GitHub; these links point at the commit this page was built from.
Starbie: common questions
What microcontroller does the Starbie use?
The Starbie is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Starbie PCB?
The Starbie measures 119 × 93 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Starbie?
7 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the Starbie design files?
From the choosye/Starbie repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Starbie design in my own project?
The repository has no license, so all rights stay with choosye. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Starbie without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k