PEBBLEC3
Computationgeek·PEBBLEC3
About the PEBBLEC3 PCB
PEBBLEC3 is an open source ESP32 PCB design by Computationgeek, published on GitHub. It is a 2-layer board measuring 28.6 × 49.8 mm, with 21 components from 17 distinct parts.
Its main chip is the ESP32-C3, from the ESP32 family. Other key parts include the AP2112K. By type, the board carries 6 resistors, 4 connectors, 4 capacitors, 3 diodes, 2 ICs and 2 switches.
It belongs with the iot & wireless, usb & debug tools and dev boards & breakouts designs in this gallery.
From the project
PebbleC3 is a compact, open-source ESP32-C3 development board designed by FruitWorks Electronics. Built as a portfolio and KiCad skill project, it packs native USB, Qwiic/STEMMA QT connectivity, and castellated edges into a small, orange form factor.
PebbleC3 is a compact, open-source ESP32-C3 development board designed by FruitWorks Electronics. Built as a portfolio and KiCad skill project, it packs native USB, Qwiic/STEMMA QT connectivity, and castellated edges into a small, orange form factor.
- ESP32-C3-WROOM-02 — RISC-V single-core @ 160MHz, 4MB Flash, 400KB SRAM, Wi-Fi + BLE 5.0 - Native USB — Direct USB-C to ESP32-C3 USB (no CH340 or CP2102), supports CDC/JTAG - AP2112K-3.3 LDO — 600mA, ultra-low dropout (350mV), SOT-23-5 - Qwiic / STEMMA QT — JST-SH 4-pin connector for plug-and-play I2C ecosystem - Castellated edges — 8-pin…
Main components on the PEBBLEC3
PEBBLEC3 bill of materials (BOM)
21 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3 | ESP32-C3-WROOM-02 | U1 |
| 1 | AP2112K | SOT-23-5 | U2 |
| 1 | USB2.0_C_16P | USB_C_Receptacle_GCT_USB4110 | J1 |
| 1 | QWIIC | JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_Vertical | J2 |
| 1 | Right_Edges | PinHeader_1x08_P2.54mm_Vertical_Mod | J3 |
| 1 | Left_Edge | PinHeader_1x08_P2.54mm_Vertical_Mod | J4 |
| 1 | RESET | SW_SPST_TS-1088-xR020 | SW1 |
| 1 | BOOT | SW_SPST_TS-1088-xR020 | SW2 |
| 1 | USERLED | LED_0805_2012Metric | D1 |
| 1 | PWRLED | LED_0805_2012Metric | D2 |
| 1 | 1N5819 | Nexperia_CFP3_SOD-123W | D4 |
| 2 | 1uF | C_0805_2012Metric | C1, C2 |
| 1 | 100nF | C_0201_0603Metric | C3 |
| 1 | 10uF | C_0805_2012Metric | C4 |
| 2 | 5.1K | R_0805_2012Metric | R1, R2 |
| 2 | 470 | R_0805_2012Metric | R3, R6 |
| 2 | 10K | R_0805_2012Metric | R4, R5 |
PEBBLEC3 design files
The KiCad project lives in the Computationgeek/PEBBLEC3 repository on GitHub; these links point at the commit this page was built from.
- LayoutESPQT.kicad_pcb
- SchematicESPQT.kicad_sch
PEBBLEC3: common questions
What microcontroller does the PEBBLEC3 use?
The PEBBLEC3 is built around the ESP32-C3, from the ESP32 family.
How big is the PEBBLEC3 PCB?
The PEBBLEC3 measures 28.6 × 49.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PEBBLEC3?
21 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the PEBBLEC3 design files?
From the Computationgeek/PEBBLEC3 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the PEBBLEC3 design in my own project?
The repository has no license, so all rights stay with Computationgeek. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the PEBBLEC3 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k