HardLabs

FYP Heater

conorcurley5·FYP_Files·KiCAD (PCB)/FYP_Heater/FYP_Heater.kicad_pcb

FYP Heater PCB layout, top view — open source ESP32 board by conorcurley5
Simulate this board

About the FYP Heater PCB

FYP Heater is an open source ESP32 PCB design by conorcurley5, published on GitHub. It is a 2-layer board measuring 120 × 120 mm, with 31 components from 21 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the TMP112XXDRL and AMS1117CD-3.3. By type, the board carries 10 resistors, 7 diodes, 6 capacitors, 3 ICs, 2 connectors and 2 switches.

From the project

Due to the quantity of code involved in this project, all files are stored in this GitHub repository. There's almost 1GB of data here, so the portfolio would end up being significantly more than 100 pages.

Due to the quantity of code involved in this project, all files are stored in this GitHub repository. There's almost 1GB of data here, so the portfolio would end up being significantly more than 100 pages.

- CCS Application - KiCAD - SolidWorks - User Interface Application

This folder holds the code for the PlatformIO-based CCS software. The primary folder in here is "(Main)FYP Project - ESP", however older revisions of the software, and revisions for different platforms, are available also.

Main components on the FYP Heater

TMP112XXDRLAMS1117CD-3.3ESP32-S3-WROOM-1

FYP Heater bill of materials (BOM)

31 components, 21 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TMP112XXDRL
TMP112xxDRL
U2
1
AMS1117CD-3.3
U3
1
ESP32-S3-WROOM-1
U4
1
IRLZ44N
Q4
1
USB_B_Micro
J1
1
SCREW_TERMINAL_01X02
Screw_Terminal_01x02
J3
2
SW_SPST
SW1, SW2
3
LESD5D5.0CT1G
D1, D2, D3
2
LED
D4, D5
2
D
D6, D8
1
1u
C1
1
10UF
10uF
C3
1
22UF
22uF
C4
1
10UF
10uF
C5
1
1UF
1uF
C6
1
0.01U
0.01u
C7
3
5k
R1, R2, R8
1
10
R3
1
47.5K
47.5k
R4
1
22.1K
22.1k
R5
Show 1 more
QtyPartRefs
4
1k
R11, R12, R13, R14

FYP Heater design files

The KiCad project lives in the conorcurley5/FYP_Files repository on GitHub; these links point at the commit this page was built from.

FYP Heater: common questions

What microcontroller does the FYP Heater use?

The FYP Heater is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the FYP Heater PCB?

The FYP Heater measures 120 × 120 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the FYP Heater?

31 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the FYP Heater design files?

From the conorcurley5/FYP_Files repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the FYP Heater design in my own project?

The repository has no license, so all rights stay with conorcurley5. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the FYP Heater without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in FYP_Files

Similar boards