SPIKE
cr1spyapple·SPIKE
About the SPIKE PCB
SPIKE is an open source ESP32 PCB design by cr1spyapple, published on GitHub. It is a 2-layer board measuring 29.3 × 56.5 mm, with 52 components from 31 distinct parts.
Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the TLV62569DRL, APS6404L-3SQRx-SN and W25Q128JVS. By type, the board carries 19 capacitors, 17 resistors, 4 ICs, 4 inductors, 3 connectors and 2 switches.
It belongs with the iot & wireless designs in this gallery.
From the project
A sleek ESP-32 microcontroller featuring additional PSRAM, plus WiFi and Bluetooth connectivity.
Designed in KiCAD as part of STASIS for Hack Club. I took up this project to learn more about PCB and MCU design. This acts as a prototype of sorts to my e-Reader project "Bebop" which will use similar hardware to this.

Main components on the SPIKE
SPIKE bill of materials (BOM)
52 components, 31 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3 | QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm_ThermalVias | U1 |
| 1 | TLV62569DRL | SOT-563 | U5 |
| 1 | APS6404L-3SQRx-SN | SOIC-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | W25Q128JVS | SOIC-8_5.3x5.3mm_P1.27mm | U7 |
| 1 | Crystal_GND24 | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 2 | Conn_01x17 | PinHeader_1x17_P2.54mm_Vertical | J1, J2 |
| 1 | USB_C_Receptacle_USB2.0_14P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J5 |
| 1 | Antenna_Dipole | Trace Antenna 2.4GHz | AE1 |
| 1 | RST | SW_Push_SPST_NO_Alps_SKRK | SW1 |
| 1 | BOOT | SW_Push_SPST_NO_Alps_SKRK | SW2 |
| 1 | LED | LED_0603_1608Metric | D1 |
| 1 | 2.0nH | L_0603_1608Metric | L1 |
| 1 | 24nH | L_0201_0603Metric | L2 |
| 1 | 1uH | L_0805_2012Metric | L4 |
| 1 | 2.4nH | L_0805_2012Metric | L5 |
| 2 | 20pF | C_0402_1005Metric | C1, C2 |
| 2 | 10uF | C_0603_1608Metric | C3, C19 |
| 5 | 1uF | C_0402_1005Metric | C4, C8, C22, C23, C34 |
| 5 | 100nF | C_0402_1005Metric | C5, C6, C7, C9, C10 |
| 2 | 1.2pF | C_0402_1005Metric | C11, C12 |
Show 11 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 4.7uF | C_0603_1608Metric | C16 |
| 1 | 10nF | C_0603_1608Metric | C33 |
| 1 | 22uF | C_0603_1608Metric | C39 |
| 1 | 499 | R_0805_2012Metric | R2 |
| 6 | 0 | R_0805_2012Metric | R3, R4, R5, R6, R7, R12 |
| 2 | 5.1k | R_0603_1608Metric | R8, R9 |
| 2 | 22 | R_0603_1608Metric | R10, R11 |
| 3 | 10K | R_0603_1608Metric | R13, R14, R19 |
| 1 | 75 | R_0603_1608Metric | R15 |
| 1 | 453k | R_0603_1608Metric | R29 |
| 1 | 100k | R_0603_1608Metric | R30 |
SPIKE design files
The KiCad project lives in the cr1spyapple/SPIKE repository on GitHub; these links point at the commit this page was built from.
- LayoutSPIKE.kicad_pcb
- SchematicSPIKE.kicad_sch
- BOMSPIKE-bom.csv
SPIKE: common questions
What microcontroller does the SPIKE use?
The SPIKE is built around the ESP32-S3, from the ESP32 family.
How big is the SPIKE PCB?
The SPIKE measures 29.3 × 56.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SPIKE?
52 components, from 31 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the SPIKE design files?
From the cr1spyapple/SPIKE repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the SPIKE design in my own project?
The repository has no license, so all rights stay with cr1spyapple. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the SPIKE without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k