SlimeVR-Tracker-Tiny
cyberpsychozz·slmvr-gaitlab·research/slmvr-rev1.9-2026-11-07/references/icrazt__SlimeVR-Tracker/1.Hardware/slimevr-tracker-tiny/SlimeVR-Tracker-Tiny.kicad_pcb
About the SlimeVR-Tracker-Tiny PCB
SlimeVR-Tracker-Tiny is an open source ESP32 PCB design by cyberpsychozz, published on GitHub. It is a 2-layer board measuring 24.5 × 34.3 mm, with 58 components from 34 distinct parts.
Its main chip is the ESP32-C3-MINI-1-N4(4MB), from the ESP32 family. Other key parts include the BNO085, LGS4084HB6 and SY8088IAAC. By type, the board carries 23 resistors, 15 capacitors, 6 connectors, 5 diodes, 4 ICs and 2 switches.
It belongs with the power & battery designs in this gallery.
From the project
1. 选用 ESP32-C3-MINI-1 小体积模组,搭载 RISC-V 32 位单核处理器,时钟频率高达 160 MHz。支持 USB CDC 串口连接,无需添加其他芯片进行 USB-串口转换。 2. 电源部分使用 SY8088IAAC 1A 同步降压调节器,相比低压降(LDO) 稳压器效率更高,在搭配 1000mAh 电池时实测至少可用10小时 3. 电池管理部分选用 LGS4084HB6 线性充电芯片,在 400mAh 充电时温度稳定,不会因芯片结温过高触发保护 4. 外壳:FDM 3D 打印外壳 + 亚克力顶部盖板,胶水粘合 5. 绑带:推荐搭
1. 选用 ESP32-C3-MINI-1 小体积模组,搭载 RISC-V 32 位单核处理器,时钟频率高达 160 MHz。支持 USB CDC 串口连接,无需添加其他芯片进行 USB-串口转换。 2. 电源部分使用 SY8088IAAC 1A 同步降压调节器,相比低压降(LDO) 稳压器效率更高,在搭配 1000mAh 电池时实测至少可用10小时 3. 电池管理部分选用 LGS4084HB6 线性充电芯片,在 400mAh 充电时温度稳定,不会因芯片结温过高触发保护 4. 外壳:FDM 3D 打印外壳 + 亚克力顶部盖板,胶水粘合 5. 绑带:推荐搭配 25mm 硅胶防滑魔术贴绑带使用 6. Pogo pin 连接器:为待设计的充电坞预留的弹簧式探针接口,目前未使用
部分元件引用自我的个人元件库 icrazt/crazt-kicad-library: Personal kicad library@ commitid 6e0f3d16fc3e03ba4c9d6a389a14d54e43484b1e,若修改工程则需要添加。
Main components on the SlimeVR-Tracker-Tiny
SlimeVR-Tracker-Tiny bill of materials (BOM)
58 components, 34 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BNO085 | LGA-28_5.2x3.8mm_P0.5mm | U1 |
| 1 | ESP32-C3-MINI-1-N4(4MB) | WIFIM-SMD_ESP32-C3-MINI-1 | U2 |
| 1 | LGS4084HB6 | SOT-23-6 | U3 |
| 1 | SY8088IAAC | SOT-23-5 | U4 |
| 1 | 32.768K | Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | Battery | Molex_PicoBlade_53261-0271_1x02-1MP_P1.25mm_Horizontal | J1 |
| 1 | OptionalPower | YZ193115035T-02025-01 | J2 |
| 1 | USB_C_Receptacle_USB2.0 | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J3 |
| 1 | Program | PinHeader_1x04_P1.27mm_Vertical | J4 |
| 1 | AUX | JST_GH_SM05B-GHS-TB_1x05-1MP_P1.25mm_Horizontal | J5 |
| 1 | AUX2 | Pad_1x05_P1.27mm | J6 |
| 1 | SW_SPDT | SW_SPDT_PCM12 | SW1 |
| 1 | SW_Push | SW_Push_SPST_NO_Alps_SKRK | SW2 |
| 1 | RED | LED_0603_1608Metric | D1 |
| 1 | GREEN | LED_0603_1608Metric | D2 |
| 1 | 1N5819WS | D_SOD-323 | D3 |
| 1 | BLUE | LED_0603_1608Metric | D4 |
| 1 | YELLOW | LED_0603_1608Metric | D5 |
| 1 | 600Ω @ 100MHz | L_0603_1608Metric | FB1 |
| 1 | MWTC252010S2R2MT | L_Sunlord_SWPA252010S | L1 |
Show 14 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 6 | 100nF | C_0402_1005Metric | C1, C2, C3, C4, C8, C15 |
| 1 | 1uF | C_0402_1005Metric | C5 |
| 2 | 12pF | C_0402_1005Metric | C6, C7 |
| 5 | 10uF | C_0402_1005Metric | C9, C11, C12, C13, C14 |
| 1 | 22pF | C_0402_1005Metric | C10 |
| 8 | 10K | R_0402_1005Metric | R1, R2, R3, R6, R7, R17, R18, R23 |
| 4 | 4.7K | R_0402_1005Metric | R4, R5, R9, R10 |
| 1 | 1K | R_0402_1005Metric | R8 |
| 1 | 1M | R_0402_1005Metric | R11 |
| 1 | 2.5K | R_0402_1005Metric | R12 |
| 4 | 2K | R_0402_1005Metric | R13, R14, R19, R21 |
| 1 | 100K | R_0402_1005Metric | R15 |
| 1 | 22K | R_0402_1005Metric | R16 |
| 2 | 5.1K | R_0402_1005Metric | R20, R22 |
SlimeVR-Tracker-Tiny design files
The KiCad project lives in the cyberpsychozz/slmvr-gaitlab repository on GitHub; these links point at the commit this page was built from.
- Layoutresearch/slmvr-rev1.9-2026-11-07/references/icrazt__SlimeVR-Tracker/1.Hardware/slimevr-tracker-tiny/SlimeVR-Tracker-Tiny.kicad_pcb
- Schematicresearch/slmvr-rev1.9-2026-11-07/references/icrazt__SlimeVR-Tracker/1.Hardware/slimevr-tracker-tiny/SlimeVR-Tracker-Tiny.kicad_sch
- BOMreverse_engineering/slmvr_rev1_9/documents/BOM_observed.csv
SlimeVR-Tracker-Tiny: common questions
What microcontroller does the SlimeVR-Tracker-Tiny use?
The SlimeVR-Tracker-Tiny is built around the ESP32-C3-MINI-1-N4(4MB), from the ESP32 family.
How big is the SlimeVR-Tracker-Tiny PCB?
The SlimeVR-Tracker-Tiny measures 24.5 × 34.3 mm, has 2 copper layers and is 1 mm thick.
How many components are on the SlimeVR-Tracker-Tiny?
58 components, from 34 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the SlimeVR-Tracker-Tiny design files?
From the cyberpsychozz/slmvr-gaitlab repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the SlimeVR-Tracker-Tiny design in my own project?
The repository has no license, so all rights stay with cyberpsychozz. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the SlimeVR-Tracker-Tiny without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in slmvr-gaitlab
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k