SlimeVR-Tracker

cyberpsychozz·slmvr-gaitlab·research/slmvr-rev1.9-2026-11-07/references/xuan25__SlimeVR-Tracker-HW/PCB/SlimeVR-Tracker.kicad_pcb

SlimeVR-Tracker PCB layout, top view — open source ESP32 board by cyberpsychozz

About the SlimeVR-Tracker PCB

SlimeVR-Tracker is an open source ESP32 PCB design by cyberpsychozz, published on GitHub. It is a 2-layer board measuring 30 × 30 mm, with 45 components from 26 distinct parts.

Its main chip is the ESP32-C3-MINI-1, from the ESP32 family. Other key parts include the BQ24075RGT, BNO08X and TPS62162DSG. By type, the board carries 21 resistors, 12 capacitors, 4 ICs, 3 connectors, 3 diodes and 1 switch.

It belongs with the power & battery and sensors designs in this gallery.

From the project

- PCB: PCB designed with KiCAD 8.0.7 - Case: Case designed with FreeCAD 1.0.0 - Adapted firmware is available here

- PCB: PCB designed with KiCAD 8.0.7 - Case: Case designed with FreeCAD 1.0.0 - Adapted firmware is available here

- IMU: BNO085; MCU: ESP32-C3 - 3D printed case - 2-layer PCB - firmware uploading via USB - 9-hour durability with 700mAh 803030 Li-Po battery - Dimension: 57mm (l) x 37mm (w) x 23mm (h) - Optimized for hand soldering (hot plate required), with enough spacing to comfortably handle 0603 SMD components and maintain adequate clearance.

Main components on the SlimeVR-Tracker

SlimeVR-Tracker bill of materials (BOM)

45 components, 26 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-C3-MINI-1
U1
1
BQ24075RGT
U2
1
BNO08X
U3
1
TPS62162DSG
U4
1
GT-USB-7010ASV
J1
1
SUR_SM02B-SURS-TF
J2
1
SUR_SM06B-SURS-TF
J3
1
SW_SPDT_PCM12
SW1
1
G
D1
1
R
D2
1
B
D3
1
2.2u
L1
5
0.1u
C1, C3, C7, C11, C12
2
10u
C2, C9
2
4.7u
C4, C5
1
22u
C6
2
1u
C8, C10
7
10k
R1, R6, R7, R12, R15, R20, R21
2
5.1k
R2, R3
3
1.5k
R4, R5, R9
Show 6 more
QtyPartRefs
1
40.2k
R8
4
2.2k
R10, R11, R13, R17
1
100k
R14
1
30k
R16
1
1.8k
R18
1
3.3k
R19

SlimeVR-Tracker design files

The KiCad project lives in the cyberpsychozz/slmvr-gaitlab repository on GitHub; these links point at the commit this page was built from.

SlimeVR-Tracker: common questions

What microcontroller does the SlimeVR-Tracker use?

The SlimeVR-Tracker is built around the ESP32-C3-MINI-1, from the ESP32 family.

How big is the SlimeVR-Tracker PCB?

The SlimeVR-Tracker measures 30 × 30 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the SlimeVR-Tracker?

45 components, from 26 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the SlimeVR-Tracker design files?

From the cyberpsychozz/slmvr-gaitlab repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the SlimeVR-Tracker design in my own project?

The repository has no license, so all rights stay with cyberpsychozz. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the SlimeVR-Tracker without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in slmvr-gaitlab

Similar boards