Meatball badge
cybre-finn·meatball-badge·hardware/nasa-badge.kicad_pcb
About the Meatball badge PCB
Meatball badge is an open source ESP32 PCB design by cybre-finn, published on GitHub. It is a 2-layer board measuring 99.7 × 81.6 mm, with 54 components from 20 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the MCP73831-2-OT, AP2114H-3.3 and FT232RL. By type, the board carries 21 resistors, 15 diodes, 5 capacitors, 4 ICs, 3 transistors and 2 connectors.
It belongs with the wearables designs in this gallery.
From the project
NASA meatball logo as a wearable PCB lanyard badge (KiCAD design files)
Wear the NASA meatball logo as a PCB lanyard badge.
Features: - illuminated vector and stars (reverse mounted LEDs) - programmable via Arduino IDE - ESP32 MCU - USB Type C interface - Li-ion battery
For (interactive) BOM see the Instructions page (german).
Main components on the Meatball badge
Meatball badge bill of materials (BOM)
54 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MCP73831-2-OT | SOT-23-5 | U1 |
| 1 | AP2114H-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | FT232RL | SSOP-28_5.3x10.2mm_P0.65mm | U3 |
| 1 | ESP32-WROOM-32 | ESP32-WROOM-32 | U4 |
| 3 | PZT3904 | SOT-223 | Q1, Q2, Q3 |
| 1 | USB_C_Receptacle_USB2.0 | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | Conn_01x04_Female | PinSocket_1x04_P2.54mm_Vertical | J2 |
| 1 | Battery_Cell | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | BT1 |
| 2 | SW_Push | SW_SPST_FSMSM | SW1, SW2 |
| 10 | LED_R | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D2, D4, D5, D7, D8, D10, D11 +2 |
| 5 | LED_W | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3, D6, D9, D12, D15 |
| 1 | MI0805K400R-10 | L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | FB1 |
| 1 | 100nF | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1 |
| 2 | 10uF | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C2, C4 |
| 2 | optional | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C3, C5 |
| 1 | 3k | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1 |
| 2 | 51k | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R2, R3 |
| 3 | 1.8K | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R4, R5, R6 |
| 10 | 82R | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R7, R8, R10, R11, R13, R14, R16, R17 +2 |
| 5 | 47R | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R9, R12, R15, R18, R21 |
Meatball badge design files
The KiCad project lives in the cybre-finn/meatball-badge repository on GitHub; these links point at the commit this page was built from.
Meatball badge: common questions
What microcontroller does the Meatball badge use?
The Meatball badge is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the Meatball badge PCB?
The Meatball badge measures 99.7 × 81.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Meatball badge?
54 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the Meatball badge design files?
From the cybre-finn/meatball-badge repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Meatball badge design in my own project?
The repository has no license, so all rights stay with cybre-finn. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Meatball badge without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k