Esp32 turd scooter controller
d0ng3o·esp32_turd_scooter_controller·kicad/board/scooter_board.kicad_pcb
About the Esp32 turd scooter controller PCB
Esp32 turd scooter controller is an open source ESP32 PCB design by d0ng3o, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 61 × 61.2 mm, with 35 components from 19 distinct parts.
Its main chip is the XIAO ESP32-C3, from the ESP32 family. Other key parts include the LSM6DS3TR-C. By type, the board carries 13 resistors, 10 capacitors, 4 diodes, 3 connectors, 2 ICs and 1 transistor.
It belongs with the robotics & motion, iot & wireless and displays & leds designs in this gallery.
From the project
Open-source ESP32-C3 replacement control board + ESP-IDF firmware for a decommissioned Bird One e-scooter, plus the reverse-engineered Lishui one-wire bus protocol.
Replacement control board for a decommissioned Bird One #590AE e-scooter. A Seeed XIAO ESP32-C3 reads the throttle and brake, talks to the Lishui motor controller over the scooter's native one-wire 3.3 V open-drain UART (115200), senses pack voltage, drives a buzzer and an addressable status LED, carries an on-board IMU for wake-on-motion, and shows telemetry on an enclosure-mounted OLED.
Main components on the Esp32 turd scooter controller
Esp32 turd scooter controller bill of materials (BOM)
35 components, 19 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LSM6DS3TR-C | LGA-14_L3.0-W2.5-P0.50-TL | U2 |
| 1 | XIAO ESP32-C3 | CONN-SMD_XIAO_ESP32C3 | U3 |
| 1 | 2N7002 | SOT-23-3_L2.9-W1.3-P1.90-LS2.4-BR | Q1 |
| 1 | Amphenol 98424-F52-12ALF | CONN-SMD_12P-P2.00-V-R2-C6-LS9.0 | J3 |
| 1 | OLED I2C JST-GH RA | JST_GH_SM04B-GHS-TB_1x04-1MP_P1.25mm_Horizontal | J4 |
| 1 | D10/SDA/SCL/5V/3V3/PACK/GND | PinHeader_1x07_P2.54mm_Vertical | J6 |
| 1 | Buzzer 5V HYG-8503A C18623826 | BUZ-SMD_4P-L8.5-W8.5-P8.50-TL-A | BZ1 |
| 1 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | LED1 |
| 3 | 3V3 | D_SOD-123 | D1, D2, D3 |
| 1 | SMF3.3A | SOD-123_L2.8-W1.8-LS3.7-RD | D4 |
| 7 | 100nF | C_0805_2012Metric | C1, C2, C3, C5, C8, C9, C11 |
| 3 | 10uF | C_0805_2012Metric | C6, C7, C10 |
| 6 | 100k | R_0805_2012Metric | R1, R2, R3, R4, R13, R14 |
| 1 | 100 | R_0805_2012Metric | R6 |
| 1 | 470k | R_0805_2012Metric | R7 |
| 1 | 33k | R_0805_2012Metric | R8 |
| 1 | 1k | R_0805_2012Metric | R9 |
| 1 | 1M | R_0805_2012Metric | R10 |
| 2 | 4.7k | R_0805_2012Metric | R11, R12 |
Esp32 turd scooter controller design files
The KiCad project lives in the d0ng3o/esp32_turd_scooter_controller repository on GitHub; these links point at the commit this page was built from.
Esp32 turd scooter controller: common questions
What microcontroller does the Esp32 turd scooter controller use?
The Esp32 turd scooter controller is built around the XIAO ESP32-C3, from the ESP32 family.
How big is the Esp32 turd scooter controller PCB?
The Esp32 turd scooter controller measures 61 × 61.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32 turd scooter controller?
35 components, from 19 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp32 turd scooter controller design files?
From the d0ng3o/esp32_turd_scooter_controller repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Esp32 turd scooter controller design in my own project?
Yes, under the terms of its GPL-3.0 license, which d0ng3o chose for the repository.
Can I test firmware for the Esp32 turd scooter controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k