EndevourDMX

Darbyshire64·EndevourDMX·Kicad/EDMX/EDMX.kicad_pcb

EndevourDMX PCB layout, top view — open source ESP32 board by Darbyshire64

About the EndevourDMX PCB

EndevourDMX is an open source ESP32 PCB design by Darbyshire64, published on GitHub under the MIT license. It is a 2-layer board measuring 143 × 75.5 mm, with 17 components from 15 distinct parts.

Its main chip is the XIAO-ESP32-C3-DIP, from the ESP32 family. Other key parts include the MAX485E. By type, the board carries 6 diodes, 5 resistors, 3 connectors, 2 ICs and 1 transistor.

It belongs with the iot & wireless and displays & leds designs in this gallery.

From the project

This is a custom DMX Tranciver Platform Designed for both reciving and controling DMX. Using an ESP32-C3 With Onboard WIFI

https://github.com/user-attachments/assets/77d9e712-4af0-4d90-8f60-33b776832eaa

It allows for DMX Passthrough so if something where to hapen to the MCU the DMX signal Could still passthrough pasiveley without power. The A,B Data lines are protected by a TVS Diode and 100 ohm resistors this cleans up any interfearence in the transmision. this is then sent the the MAX845E Chip to convert the data into easy to recive serieal data for the ESP. As the DMX lighting protocol uses RS845 Serieal the MAX845E is neccesary to control TX/RX the signal.

EndevourDMX, from the project README
From the project README

Main components on the EndevourDMX

EndevourDMX bill of materials (BOM)

17 components, 15 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
MAX485E
U1
1
XIAO-ESP32-C3-DIP
U2
1
2N3904
Q1
1
XLR3 IN
J1
1
Conn_01x04
J2
1
XLR3 OUT
J3
1
D
D1
2
1.5KExxCA
D2, D3
1
DMX Status
D4
1
WiFi Status
D5
1
Light Control
D6
1
3.3kΩ
R1
1
1.8kΩ
R2
1
120Ω
R3
2
100Ω
R4, R5

EndevourDMX design files

The KiCad project lives in the Darbyshire64/EndevourDMX repository on GitHub; these links point at the commit this page was built from.

EndevourDMX: common questions

What microcontroller does the EndevourDMX use?

The EndevourDMX is built around the XIAO-ESP32-C3-DIP, from the ESP32 family.

How big is the EndevourDMX PCB?

The EndevourDMX measures 143 × 75.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the EndevourDMX?

17 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the EndevourDMX design files?

From the Darbyshire64/EndevourDMX repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the EndevourDMX design in my own project?

Yes, under the terms of its MIT license, which Darbyshire64 chose for the repository.

Can I test firmware for the EndevourDMX without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards