Esp32s31-dev
DataFlux-Robot·fluxpcb·projects/esp32s31-dev/pcb/board/esp32s31-dev.kicad_pcb
About the Esp32s31-dev PCB
Esp32s31-dev is an open source ESP32 PCB design by DataFlux-Robot, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 65 × 30 mm, with 19 components from 15 distinct parts.
Its main chip is the ESP32-S31-WROOM-3U, from the ESP32 family. Other key parts include the AP2112K-3.3. By type, the board carries 6 resistors, 4 connectors, 3 capacitors, 2 switches, 2 diodes and 1 IC.
From the project
全自动AI电路设计流水线: 需求→选型→原理图→PCB→验收仿真→固件,六环节门禁闭环 | Six-stage automated circuit design pipeline with machine-checkable verification gates
FluxPCB turns a sentence into a manufacturable PCB and its firmware — and it refuses to call anything "done" until 16 machine-checkable gates agree. No gate, no glory.
LLMs write beautiful netlists — and occasionally invent pin numbers. FluxPCB's rule: the LLM generates; deterministic solvers and real EDA tools decide. A failed gate emits structured feedback, the pipeline regenerates, retries are bounded. "Complete" is a physical verdict, not a vibe.

Main components on the Esp32s31-dev
Esp32s31-dev bill of materials (BOM)
19 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP2112K-3.3 | SOT-23-5 | U1 |
| 1 | ESP32-S31-WROOM-3U | ESP32-S31-WROOM-3 | MOD1 |
| 1 | HDR-TOP | PinHeader_1x14_P2.54mm_Vertical | J1 |
| 1 | HDR-BOT | PinHeader_1x14_P2.54mm_Vertical | J2 |
| 1 | HDR-PROG | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | USB-C | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J4 |
| 1 | RESET | SW_Push_1P1T_NO_CK_KMR2 | SW1 |
| 1 | BOOT | SW_Push_1P1T_NO_CK_KMR2 | SW2 |
| 1 | RED | LED_0603_1608Metric | D1 |
| 1 | BLUE | LED_0603_1608Metric | D2 |
| 2 | 10uF | C_0805_2012Metric | C1, C2 |
| 1 | 100nF | C_0603_1608Metric | C3 |
| 2 | 1k | R_0603_1608Metric | R1, R4 |
| 2 | 10k | R_0603_1608Metric | R2, R3 |
| 2 | 5.1k | R_0603_1608Metric | R5, R6 |
Esp32s31-dev design files
The KiCad project lives in the DataFlux-Robot/fluxpcb repository on GitHub; these links point at the commit this page was built from.
Esp32s31-dev: common questions
What microcontroller does the Esp32s31-dev use?
The Esp32s31-dev is built around the ESP32-S31-WROOM-3U, from the ESP32 family.
How big is the Esp32s31-dev PCB?
The Esp32s31-dev measures 65 × 30 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32s31-dev?
19 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32s31-dev design files?
From the DataFlux-Robot/fluxpcb repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Esp32s31-dev design in my own project?
Yes, under the terms of its Apache-2.0 license, which DataFlux-Robot chose for the repository.
Can I test firmware for the Esp32s31-dev without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in fluxpcb
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k