Automatic irrigation system
david-oliver-karunia·automatic-irrigation-system·electronics/automatic-irrigation-system.kicad_sch
About the Automatic irrigation system PCB
Automatic irrigation system is an open source ESP32 PCB design by david-oliver-karunia, published on GitHub under the MIT license. It is a board, with 9 components from 9 distinct parts.
Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the ER_OLEDM0.91_1x-I2C, Moisture_sensor, HC-SR04 and ESP8266EX. By type, the board carries 5 ICs, 1 module, 1 relay, 1 diode and 1 capacitor.
It belongs with the sensors and iot & wireless designs in this gallery.
From the project
An ESP32-based smart irrigation system that combines soil moisture, environmental sensors, reservoir monitoring, weather forecasts, and intelligent watering control.
An ESP32-S3-based automatic irrigation system that monitors soil moisture, estimates the water level in a reservoir, and controls a water pump when the plant's soil becomes too dry.
The project explores practical applications of embedded systems, sensors, automation, web interfaces, and intelligent decision-making in plant care and small-scale agriculture.
The system uses a soil-moisture sensor to determine whether the soil is dry and an HC-SR04 ultrasonic sensor to estimate the remaining water in the reservoir.
Main components on the Automatic irrigation system
Automatic irrigation system bill of materials (BOM)
9 components, 9 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ER_OLEDM0.91_1x-I2C | ER_OLEDM0.91_1x-I2C | U1 |
| 1 | Moisture_sensor | Texas_PWSON-N6 | U2 |
| 1 | HC-SR04 | U3 | |
| 1 | ESP8266EX | QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm | U4 |
| 1 | ESP32-S3 | QFN-56-1EP_7x7mm_P0.4mm_EP4x4mm | U6 |
| 1 | Water_pump | M1 | |
| 1 | Motor_relay | K1 | |
| 1 | 1N5819 | D1 | |
| 1 | 100nF | C1 |
Automatic irrigation system design files
The KiCad project lives in the david-oliver-karunia/automatic-irrigation-system repository on GitHub; these links point at the commit this page was built from.
Automatic irrigation system: common questions
What microcontroller does the Automatic irrigation system use?
The Automatic irrigation system is built around the ESP32-S3, from the ESP32 family.
How many components are on the Automatic irrigation system?
9 components, from 9 distinct parts. The full bill of materials is listed on this page.
Where can I download the Automatic irrigation system design files?
From the david-oliver-karunia/automatic-irrigation-system repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Automatic irrigation system design in my own project?
Yes, under the terms of its MIT license, which david-oliver-karunia chose for the repository.
Can I test firmware for the Automatic irrigation system without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k