Ghostlight node
DefeatedWarrior·ghostlight-node·hardware/kicad/ghostlight-node-rev1.kicad_pcb
About the Ghostlight node PCB
Ghostlight node is an open source ESP32 PCB design by DefeatedWarrior, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 100 × 100 mm, with 82 components from 47 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8, from the ESP32 family. Other key parts include the W5500, SN65HVD72DR, AMS1117-3.3 and USBLC6-2SC6. By type, the board carries 26 resistors, 23 capacitors, 11 connectors, 7 diodes, 6 ICs and 2 transistors.
It belongs with the iot & wireless designs in this gallery.
From the project
Open-source Art-Net/sACN to DMX512 node, ESP32-S3 + W5500 + PoE
A low-cost, open-source Art-Net / sACN → DMX512 node with PoE
Two RDM-capable DMX ports · ESP32-S3 · W5500 Ethernet · 802.3af PoE · USB-C
Docs · Wiki pages · Ordering · Known issues · Firmware
A ghost light is the single bulb left burning on an otherwise dark stage. The node does the same quiet job: it keeps the rig alive and listening while nothing else is on. The goal is a DMX node you can build for a small fraction of the cost of commercial units, with every file open.

Main components on the Ghostlight node
Ghostlight node bill of materials (BOM)
82 components, 47 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N8 | ESP32-S3-WROOM-1 | U1 |
| 1 | W5500 | LQFP-48_7x7mm_P0.5mm | U2 |
| 2 | SN65HVD72DR | SOIC-8_3.9x4.9mm_P1.27mm | U3, U4 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U5 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U6 |
| 2 | 2N7002 | SOT-23 | Q1, Q2 |
| 1 | 25MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | HR871150C | RJ45_Hanrun_HR871150C | J1 |
| 1 | DMX1 | TerminalBlock_bornier-3_P5.08mm | J2 |
| 1 | DMX1_OUT | TerminalBlock_bornier-3_P5.08mm | J2O |
| 1 | TERM1 | PinHeader_1x02_P2.54mm_Vertical | J2T |
| 1 | DMX2 | TerminalBlock_bornier-3_P5.08mm | J3 |
| 1 | DMX2_OUT | TerminalBlock_bornier-3_P5.08mm | J3O |
| 1 | TERM2 | PinHeader_1x02_P2.54mm_Vertical | J3T |
| 1 | USB-C (device/sink) | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J4 |
| 1 | PORT3/EXPANSION | PinHeader_1x12_P2.54mm_Vertical | J5 |
| 1 | 5V_EXT (PoE splitter / DC) | PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | DEBUG UART0 (GND/TX/RX) | PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | PTC 1.1A | Fuse_1206_3216Metric | F1 |
| 1 | DP9700-5V | PoE_SDAPO_DP9700 | PS1 |
Show 27 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BOOT | SW_SPST_TL3342 | SW1 |
| 1 | RESET | SW_SPST_TL3342 | SW2 |
| 1 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | LED1 |
| 2 | SM712 | SOT-23 | D1, D2 |
| 3 | SS14 | D_SMA | D3, D4, D5 |
| 1 | P1 | LED_0603_1608Metric | D30 |
| 1 | P2 | LED_0603_1608Metric | D40 |
| 1 | FB 120R@100MHz | L_0603_1608Metric | L1 |
| 4 | 10uF | C_0805_2012Metric | C1, C6, C14, C18 |
| 10 | 100nF | C_0603_1608Metric | C2, C4, C10, C11, C12, C13, C15, C21 +2 |
| 1 | 1uF | C_0603_1608Metric | C3 |
| 2 | 220uF | CP_Elec_6.3x5.4 | C5, C50 |
| 1 | 22uF | C_0805_2012Metric | C7 |
| 1 | 22nF | C_0603_1608Metric | C16 |
| 1 | 4.7uF | C_0805_2012Metric | C17 |
| 2 | 18pF | C_0603_1608Metric | C19, C20 |
| 1 | 10nF | C_0603_1608Metric | C23 |
| 8 | 10k | R_0603_1608Metric | R1, R5, R8, R9, R10, R11, R30, R40 |
| 1 | 330 | R_0603_1608Metric | R2 |
| 2 | 5.1k | R_0603_1608Metric | R3, R4 |
| 1 | 12.4k 1% | R_0603_1608Metric | R6 |
| 2 | 1M | R_0603_1608Metric | R7, R12 |
| 4 | 240 1% | R_0603_1608Metric | R31, R32, R41, R42 |
| 2 | 100k | R_0603_1608Metric | R33, R43 |
| 2 | 120 1% | R_0603_1608Metric | R34, R44 |
| 2 | 1k | R_0603_1608Metric | R35, R45 |
| 2 | 220 | R_0603_1608Metric | R50, R51 |
Ghostlight node design files
The KiCad project lives in the DefeatedWarrior/ghostlight-node repository on GitHub; these links point at the commit this page was built from.
Ghostlight node: common questions
What microcontroller does the Ghostlight node use?
The Ghostlight node is built around the ESP32-S3-WROOM-1-N8, from the ESP32 family.
How big is the Ghostlight node PCB?
The Ghostlight node measures 100 × 100 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Ghostlight node?
82 components, from 47 distinct parts. The full bill of materials is listed on this page.
Where can I download the Ghostlight node design files?
From the DefeatedWarrior/ghostlight-node repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Ghostlight node design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which DefeatedWarrior chose for the repository.
Can I test firmware for the Ghostlight node without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k