Hardware esp32-ethernet
dnd-global·hardware-esp32-ethernet·kicad/esp32-eth-uart-module.kicad_pcb
About the Hardware esp32-ethernet PCB
Hardware esp32-ethernet is an open source ESP32 PCB design by dnd-global, published on GitHub. It is a 2-layer board measuring 80 × 66 mm, with 73 components from 44 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8, from the ESP32 family. Other key parts include the LMR36520, CA-IS3642HVW, SN74LVC1G17DBVR and W5500. By type, the board carries 33 capacitors, 20 resistors, 5 ICs, 3 connectors, 3 diodes and 3 inductors.
It belongs with the iot & wireless designs in this gallery.
From the project
Module nối một thiết bị có cổng UART TTL 3,3 V vào mạng. Tín hiệu UART đi qua tầng cách ly 5 kV, rồi ESP32-S3 đưa dữ liệu lên mạng bằng Ethernet hoặc Wi-Fi. Mạch chạy nguồn 9–36 V.
Module nối một thiết bị có cổng UART TTL 3,3 V vào mạng. Tín hiệu UART đi qua tầng cách ly 5 kV, rồi ESP32-S3 đưa dữ liệu lên mạng bằng Ethernet hoặc Wi-Fi. Mạch chạy nguồn 9–36 V.
Tình trạng: Rev B, chưa sản xuất. Mạch đã đi dây xong, qua kiểm tra luật thiết kế của KiCad và sắp đặt 5 mạch thử. Mọi thứ trong kho này chưa được kiểm chứng trên mạch thật.
Rất mong nhận góp ý qua mục Issues, nhất là ở bốn chỗ:

Main components on the Hardware esp32-ethernet
Hardware esp32-ethernet bill of materials (BOM)
73 components, 44 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LMR36520 | POWERPAD-SO-8_L4.9-W3.9-P1.27-LS6.0-BL-EP | U1 |
| 1 | ESP32-S3-WROOM-1-N8 | WIFIM-SMD_ESP32-S3-WROOM-1-N8 | U2 |
| 1 | CA-IS3642HVW | SOIC-16_L10.3-W7.5-P1.27-LS10.3-TL | U3 |
| 1 | SN74LVC1G17DBVR 74LVC1G17 | SOT-25-5_L3.0-W1.8-P0.95-LS3.0-BL | U4 |
| 1 | W5500 | LQFP-48_7x7mm_P0.5mm | U5 |
| 1 | C9006 25MHz 12pF | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | C474952 KF128-5.08-2P (+ / -) | CONN-TH_2P-P5.08_KF128-5.08-2P | J1 |
| 1 | HR911105A | RJ45-TH_HR911105A | J3 |
| 1 | C165948 UART-ISO | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J6 |
| 1 | C70113 PTC 0.5A 60V | F1812 | F1 |
| 1 | C318884 RESET | SW-SMD_4P-L5.1-W5.1-P3.70-LS6.5-TL_H1.5 | SW1 |
| 1 | C318884 BOOT | SW-SMD_4P-L5.1-W5.1-P3.70-LS6.5-TL_H1.5 | SW2 |
| 1 | C2286 PWR red | LED_0603_1608Metric | LED1 |
| 1 | C2290 STATUS white | LED_0603_1608Metric | LED2 |
| 1 | SS210 | D_SMA | D1 |
| 1 | SMBJ36A | D_SMB | D2 |
| 1 | PESD5V0S2BT | SOT-23 | D3 |
| 1 | C14709 120R@100MHz | L_0603_1608Metric | FB1 |
| 1 | 10UH 10uH | IND-SMD_L4.0-W4.0 | L1 |
| 1 | C357230 6.8uH 4A | IND-SMD_L7.0-W6.6 | L2 |
Show 24 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | C381466 4.7uF 100V | C_1210_3225Metric | C1, C2, C3 |
| 1 | C36911431 220nF 100V | C_0603_1608Metric | C4 |
| 1 | C48971005 47uF 63V | CP_Elec_6.3x7.7 | C5 |
| 10 | 100NF 100nF | C_0603_1608Metric | C6, C12, C16, C18, C21, C28, C29, C30 +2 |
| 3 | 1UF 1uF | C_0603_1608Metric | C7, C13, C17 |
| 4 | C12891 22uF 25V | C_1206_3216Metric | C8, C9, C10, C11 |
| 3 | 10UF 10uF | C_0805_2012Metric | C14, C15, C32 |
| 1 | 22NF 22nF | C_0603_1608Metric | C22 |
| 2 | 6.8NF 6.8nF | C_0603_1608Metric | C23, C24 |
| 2 | 10NF 10nF | C_0603_1608Metric | C25, C27 |
| 1 | 4.7UF 4.7uF | C_0603_1608Metric | C26 |
| 2 | 18PF 18pF | C_0603_1608Metric | C34, C35 |
| 1 | 51K 51k | R_0603_1608Metric | R1 |
| 1 | 22K 22k | R_0603_1608Metric | R2 |
| 1 | 1k | R_0603_1608Metric | R3 |
| 1 | 150R | R_0603_1608Metric | R4 |
| 1 | 100R | R_0603_1608Metric | R6 |
| 1 | 220R | R_0603_1608Metric | R7 |
| 5 | 10K 10k | R_0603_1608Metric | R8, R9, R19, R20, R21 |
| 1 | 1M | R_0603_1608Metric | R10 |
| 4 | C23185 49.9R 1% | R_0603_1608Metric | R11, R12, R14, R15 |
| 1 | 10R | R_0603_1608Metric | R13 |
| 2 | 330R | R_0603_1608Metric | R16, R17 |
| 1 | C2930060 12.4k 1% | R_0603_1608Metric | R18 |
Hardware esp32-ethernet design files
The KiCad project lives in the dnd-global/hardware-esp32-ethernet repository on GitHub; these links point at the commit this page was built from.
Hardware esp32-ethernet: common questions
What microcontroller does the Hardware esp32-ethernet use?
The Hardware esp32-ethernet is built around the ESP32-S3-WROOM-1-N8, from the ESP32 family.
How big is the Hardware esp32-ethernet PCB?
The Hardware esp32-ethernet measures 80 × 66 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Hardware esp32-ethernet?
73 components, from 44 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Hardware esp32-ethernet design files?
From the dnd-global/hardware-esp32-ethernet repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Hardware esp32-ethernet design in my own project?
The repository has no license, so all rights stay with dnd-global. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Hardware esp32-ethernet without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k