Board
dshills·KiCadAI·examples/board-family-v1/fast/board.kicad_pcb
About the Board
Board is an open source ESP32 PCB design by dshills, published on GitHub under the MIT license. It is a 2-layer board measuring 120 × 80 mm, with 17 components from 12 distinct parts.
Its main chip is the ESP32-WROOM-32E-N4, from the ESP32 family. Other key parts include the BMP280. By type, the board carries 6 capacitors, 4 resistors, 3 connectors, 2 ICs and 2 switches.
It belongs with the iot & wireless designs in this gallery.
From the project
AI-assisted KiCad design toolkit with Go CLI, direct schematic/PCB writers, validation, and pinmap checks.
These three complete projects were copied byte-for-byte from the successful offline acceptance run acceptance-configurations-04; no generated board was repaired manually. Open each board.kicadpro` in KiCad 10.0.3:
- standard: 4.7 kΩ pull-ups, 100 kHz, ≤200 pF total bus. - fast: 2.2 kΩ pull-ups, 400 kHz, ≤100 pF total bus. - low_current: 10 kΩ pull-ups, 100 kHz, ≤100 pF total bus.
Main components on the Board
Board bill of materials (BOM)
17 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32E-N4 Espressif | ESP32-WROOM-32E | U1 |
| 1 | BMP280 BMP280 0x76 Bosch Sensortec | Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U2 |
| 1 | TSW-102-07-L-S 3V3 INPUT Samtec | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | TSW-104-07-L-S 3V3 UART Samtec | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | TSW-106-07-L-S GPIO I2C SPI Samtec | PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | B3U-1000P RESET Omron | SW_SPST_B3U-1000P | SW1 |
| 1 | B3U-1000P BOOT Omron | SW_SPST_B3U-1000P | SW2 |
| 4 | GRM21BR71H104KA01L 100nF Murata | C_0805_2012Metric | C1, C4, C5, C6 |
| 1 | GRM21BR61A106KE19L 10uF Murata | C_0805_2012Metric | C2 |
| 1 | GCM21BR71H105KA03L 1uF Murata | C_0805_2012Metric | C3 |
| 2 | RC0805FR-0710KL 10k Yageo | R_0805_2012Metric | R1, R2 |
| 2 | RC0805FR-072K2L 2.2k Yageo | R_0805_2012Metric | R3, R4 |
Board design files
The KiCad project lives in the dshills/KiCadAI repository on GitHub; these links point at the commit this page was built from.
Board: common questions
What microcontroller does the Board use?
The Board is built around the ESP32-WROOM-32E-N4, from the ESP32 family.
How big is the Board?
The Board measures 120 × 80 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Board?
17 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Board design files?
From the dshills/KiCadAI repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Board design in my own project?
Yes, under the terms of its MIT license, which dshills chose for the repository.
Can I test firmware for the Board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in KiCadAI
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k