ECE 445L Lab 7
About the ECE 445L Lab 7 PCB
ECE 445L Lab 7 is an open source ESP8266 PCB design by DylanMeeks, published on GitHub. It is a 2-layer board measuring 115 × 94 mm, with 14 components from 14 distinct parts.
Its main chip is the ESP8266-01/ESP-01, from the ESP8266 family. Other key parts include the EK-TM4C123GXL and Adafruit ST7735R. By type, the board carries 5 switches, 3 ICs, 2 capacitors, 1 transistor, 1 speaker and 1 diode.
From the project
For 319K/445L Lab 6 or 7, use the marked file. Otherwise use ECE445L_Starter.
Main components on the ECE 445L Lab 7
ECE 445L Lab 7 bill of materials (BOM)
14 components, 14 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | EK-TM4C123GXL Texas Instruments | ti_EKTM4C123GXL | U1 |
| 1 | Adafruit ST7735R Adafruit | adafruit_st7735r2 | U2 |
| 1 | ESP8266-01/ESP-01 SparkFun | PinHeader_2x04_P2.54mm_Vertical | U3 |
| 1 | IRLD024PBF Vishay | DIP920W60P254L490H457Q4N | Q1 |
| 1 | Speaker | PinHeader_1x02_P2.54mm_Vertical | LS1 |
| 1 | UP | SW_PUSH_6mm | SW1 |
| 1 | DOWN | SW_PUSH_6mm | SW2 |
| 1 | LEFT | SW_PUSH_6mm | SW3 |
| 1 | RIGHT | SW_PUSH_6mm | SW4 |
| 1 | MODE | SW_PUSH_6mm | SW5 |
| 1 | 1N914 onsemi | D_P6.35mm_Horizontal | D1 |
| 1 | 100nF | C_Axial_200mil | C1 |
| 1 | 4.7uF | CP_Radial_Tantal200mil | C2 |
| 1 | 10k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
ECE 445L Lab 7 design files
The KiCad project lives in the DylanMeeks/ece445l-lab7-10 repository on GitHub; these links point at the commit this page was built from.
ECE 445L Lab 7: common questions
What microcontroller does the ECE 445L Lab 7 use?
The ECE 445L Lab 7 is built around the ESP8266-01/ESP-01, from the ESP8266 family.
How big is the ECE 445L Lab 7 PCB?
The ECE 445L Lab 7 measures 115 × 94 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ECE 445L Lab 7?
14 components, from 14 distinct parts. The full bill of materials is listed on this page.
Where can I download the ECE 445L Lab 7 design files?
From the DylanMeeks/ece445l-lab7-10 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the ECE 445L Lab 7 design in my own project?
The repository has no license, so all rights stay with DylanMeeks. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ECE 445L Lab 7 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.
More boards in ece445l-lab7-10
ESP8266ECE445L Final Project
152.4 × 127 mm241 parts2LNo license0
Robotics System Learning Kit
128.3 × 129.5 mm49 parts2LNo license0
ECE 319K Baseline Project
114.3 × 88.9 mm40 parts2LNo license0
ECE 445L Lab 6
114.4 × 88.9 mm28 parts2LNo license0
ESP8266ECE 445L Baseline Project
115 × 94 mm16 parts2LNo license0
Similar boards
ESP8266ESP8266ControllerCircuit
stuartpittaway
75 × 30 mm20 parts2LCC-BY-NC-4.01.1k
ESP8266HASwitchPlate
aderusha
60 × 40 mm8 parts2LMIT738
ESP8266RatGDO-OpenSource-D1Mini-ESP8266
Kaldek
47.8 × 63.3 mm12 parts2LMIT506
ESP8266Goatgdo
32.9 × 53.3 mm23 parts2LMIT506
ESP8266RatGDO-OpenSource-Bare-ESP8266
55 × 82.7 mm20 parts2LMIT506
ESP8266Iaq board
nkitanov
70.1 × 43.2 mm17 parts2LNo license398