Custom bike computer
eastmohan·custom-bike-computer·PCB/bike_computer.kicad_sch
About the Custom bike computer PCB
Custom bike computer is an open source ESP32 PCB design by eastmohan, published on GitHub. It is a board, with 13 components from 13 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the NEO-M8N-0, MAX17048G_T10 and AP2112K-3.3. By type, the board carries 4 ICs, 3 connectors, 3 switches, 1 battery holder, 1 diode and 1 resistor.
It belongs with the iot & wireless and displays & leds designs in this gallery.
From the project
I am making this as a low power bike computer. It will use an e-ink display for power efficiency. I'm also making a cadence sensor to go with it, which will connect with bluetooth. If I have time, I will also have it read heart rate data from any HRM, including watches that can b
I am making this as a low power bike computer. It will use an e-ink display for power efficiency. I'm also making a cadence sensor to go with it, which will connect with bluetooth. If I have time, I will also have it read heart rate data from any HRM, including watches that can broadcast heart rate. The bike computer will have a custom PCB so vibrations during rides are less likely to disrupt wiring.
Main components on the Custom bike computer
Custom bike computer bill of materials (BOM)
13 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | NEO-M8N-0 | XCVR_NEO-M8N-0 | U2 |
| 1 | MAX17048G_T10 | SON50P200X200X80-9N | U3 |
| 1 | AP2112K-3.3 | SOT-23-5 | U4 |
| 1 | MicroSD Card SPI Interface | J1 | |
| 1 | Conn_01x08 | J2 | |
| 1 | Conn_01x06 | J3 | |
| 1 | 3.7V LiPo | BT1 | |
| 1 | EG1218 | SW_EG1218 | S1 |
| 1 | SW_SPST | SW1 | |
| 1 | SW_Push | SW2 | |
| 1 | 1N5819 | D_DO-41_SOD81_P10.16mm_Horizontal | D1 |
| 1 | 10k | R1 |
Custom bike computer design files
The KiCad project lives in the eastmohan/custom-bike-computer repository on GitHub; these links point at the commit this page was built from.
- SchematicPCB/bike_computer.kicad_sch
Custom bike computer: common questions
What microcontroller does the Custom bike computer use?
The Custom bike computer is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How many components are on the Custom bike computer?
13 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the Custom bike computer design files?
From the eastmohan/custom-bike-computer repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Custom bike computer design in my own project?
The repository has no license, so all rights stay with eastmohan. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Custom bike computer without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k