Starbie
emdcomputer-crypto·Starbie·Hardware/Project.kicad_pcb
About the Starbie PCB
Starbie is an open source ESP32 PCB design by emdcomputer-crypto, published on GitHub. It is a 2-layer board measuring 123.8 × 105 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches and 1 resistor.
It belongs with the displays & leds, sensors and keyboards designs in this gallery.
From the project
Making a starbie
Starbie is a small virtual pet PCB made with a XIAO ESP32-C3. It uses a 0.96-inch OLED screen to show an animated pet menus and different stats. The project also has two buttons an MPU6050 motion sensor, and a DHT11 temperature and humidity sensor.
This is my Week 1 PCB project for Hack Club Half Life. I designed the schematic and PCB in KiCad, routed the traces, added a ground pour, checked the board with the Design Rules Checker, and prepared the fabrication files.
Main components on the Starbie
Starbie bill of materials (BOM)
7 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C6-DIP | U1 |
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U2 |
| 1 | Conn_01x04_Pin | Display_128x64_096_I2C | J1 |
| 1 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J2 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | 10k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
Starbie design files
The KiCad project lives in the emdcomputer-crypto/Starbie repository on GitHub; these links point at the commit this page was built from.
- LayoutHardware/Project.kicad_pcb
- SchematicHardware/Project.kicad_sch
Starbie: common questions
What microcontroller does the Starbie use?
The Starbie is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Starbie PCB?
The Starbie measures 123.8 × 105 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Starbie?
7 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the Starbie design files?
From the emdcomputer-crypto/Starbie repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Starbie design in my own project?
The repository has no license, so all rights stay with emdcomputer-crypto. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Starbie without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k