Micro ROSbot
emericarhantdev·micro_ROSbot
About the Micro ROSbot PCB
Micro ROSbot is an open source ESP32 PCB design by emericarhantdev, published on GitHub. It is a 2-layer board measuring 98.7 × 96.5 mm, with 126 components from 81 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the TLV76701DGNR, MPU-6050 and TB6612FNG,C,8,EL. By type, the board carries 31 resistors, 27 capacitors, 18 connectors, 7 ICs, 7 diodes and 4 transistors.
From the project
Power/IO board for a Small MicroROS-based robot project. Contains KiCad schematics/PCB, custom symbols/footprints, and fabrication outputs (Gerbers + drills).

Main components on the Micro ROSbot
Micro ROSbot bill of materials (BOM)
126 components, 81 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TLV76701DGNR LDO_1.475V | SOP65P490X110-9N | IC1 |
| 1 | TLV76701DGNR LDO_3.3V | SOP65P490X110-9N | IC2 |
| 1 | TLV76701DGNR LDO_6V | SOP65P490X110-9N | IC3 |
| 1 | ESP32-S3-WROOM-1-N16R8 | ESP32S3WROOM1N16R8 | IC4 |
| 1 | MPU-6050 | MPU6050 | IC5 |
| 1 | TB6612FNG,C,8,EL | SOP65P760X160-24N | IC6 |
| 1 | TLV76701DGNR LDO_3.3V_bis | SOP65P490X110-9N | IC7 |
| 3 | DMN3065LW_Mosfet | SOT65P210X110-3N | Q1, Q2, Q3 |
| 1 | DMN3065LW-7 | SOT65P210X110-3N | Q4 |
| 1 | JST_XH_BAU | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J1 |
| 1 | JST_BAT_2.54mm | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J2 |
| 1 | Motor-encoder_B | JST_ZH_1x06_P1.5mm_no_Connector | J3 |
| 1 | IR_sensor_1_connector | JST_ZH_1x05_P1.50mm_Vertical | J4 |
| 1 | IR_sensor_2_connector | JST_ZH_1x05_P1.50mm_Vertical | J5 |
| 1 | USB3075-30-A Micro_USB_pads_USB3075-30-A | USB307530A | J6 |
| 1 | IR_sensor_1_connector_main_board | JST_ZH_1x05_P1.50mm_Vertical | J7 |
| 1 | IR_sensor_2_connector_main_board | JST_ZH_1x05_P1.50mm_Vertical | J8 |
| 1 | IR_sensor_3_connector_main_board | JST_ZH_1x05_P1.50mm_Vertical | J9 |
| 1 | unused_pin_3 | PinSocket_1x07_P2.54mm_Vertical | J10 |
| 1 | JST_Ruban_LED | JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J11 |
Show 61 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Motor-encoder_A | JST_ZH_1x06_P1.5mm_no_Connector | J12 |
| 1 | IR_sensor_3_connector | JST_ZH_1x05_P1.50mm_Vertical | J13 |
| 1 | Servo_JTS_PH_3pin | JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J14 |
| 1 | unused_pin_2 | PinSocket_1x02_P2.54mm_Vertical | J15 |
| 1 | GND_Pins | PinSocket_1x04_P2.54mm_Vertical | J16 |
| 1 | unused_pin_1 | PinSocket_1x03_P2.54mm_Vertical | J17 |
| 1 | JST_Jack_2.54mm | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J20 |
| 1 | EncoderA_C1_TP | S275146R | Coder1_A1 |
| 1 | EncoderB_C1_TP | S275146R | Coder1_B1 |
| 3 | ~ | IR_receiver_TSSP77038TT | IR_rec_1, IR_rec_2, IR_rec_3 |
| 1 | IMB03ITS IMB06ITS | IMB03ITS | K1 |
| 1 | CMT-0525-75-SMT-TR | CMT052575SMTTR | LS1 |
| 2 | PWM_B_TP | S275146R | PWM-A1, TPPWM-B1 |
| 1 | SS312SAH4 | SS312SAH4 | S1 |
| 1 | PTS810SJM250SMTRLFS RST_button | PTS810SJG250SMTRLFS | S2 |
| 1 | PTS810SJM250SMTRLFS BOOT_button | PTS810SJG250SMTRLFS | S3 |
| 1 | 1.475V_TP | S275146R | TP1.475V1 |
| 1 | 3.3V_TP | S275146R | TP3.3V_1 |
| 1 | 3.3V_usb_TP | S275146R | TP3.3V_2 |
| 1 | 6V_TP | S275146R | TP6V1 |
| 1 | 9V_TP | S275146R | TPBAT1 |
| 1 | Buzzer_PWM_TP | S275146R | TPBuzzer1 |
| 1 | EN_pin_TP | S275146R | TPEN1 |
| 1 | IR_LED_1_TP | S275146R | TPIR-LED1 |
| 2 | IR_LED_3_TP | S275146R | TPIR-LED2, TPIR-LED3 |
| 1 | IR_REC_1_res_TP | S275146R | TPIR-Rec1 |
| 1 | IR_LED_1_Mosfet_TP | S275146R | TPPOW-IR-LED1 |
| 1 | Data_Ruban_TP | S275146R | TPRuban_LED1 |
| 1 | IMU_SCL_TP | S275146R | TPSCL1 |
| 1 | IMU_SDA_TP | S275146R | TPSDA1 |
| 1 | tirette_TP | S275146R | Tirette1 |
| 1 | VAL** | mouse-bite-2mm-slot | mouse-bite-2mm-slot |
| 3 | TSAL6200 | TSAL6200 | LED1, LED2, LED3 |
| 1 | shottky_byass_1 | SOD2512X113N | D1 |
| 1 | shottky_byass_2 | SOD2512X113N | D2 |
| 1 | shottky_byass_3 | SOD2512X113N | D3 |
| 1 | 6V_LED | ASCKCG00NW5X5020302 | D4 |
| 1 | 3.3V_LED | ASCKCG00NW5X5020302 | D5 |
| 1 | shottky_byass_4 | SOD2512X113N | D7 |
| 1 | 3.3V_usb_LED | ASCKCG00NW5X5020302 | D8 |
| 6 | 2.2u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C6, C9, C21, C22, C27 |
| 3 | 10p | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C5, C8 |
| 4 | 1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C4, C7, C13 |
| 3 | 1uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10, C11, C12 |
| 1 | 10n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C14 |
| 7 | 0.1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C15, C17, C18, C20, C23, C25, C26 |
| 1 | 2.2n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C16 |
| 1 | 220u | CAPPM3528X210N | C19 |
| 1 | 10u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C24 |
| 1 | 500k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 592k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 4 | 2M | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R5, R9, R10 |
| 1 | 640k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | 732k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
| 1 | 135 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
| 3 | 15 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8, R14, R20 |
| 3 | 1.27 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11, R12, R13 |
| 2 | 2.2k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15, R16 |
| 1 | 4.7k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R17 |
| 12 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R18, R19, R21, R22, R23, R24, R25, R26 +4 |
| 1 | 3 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R28 |
Micro ROSbot design files
The KiCad project lives in the emericarhantdev/micro_ROSbot repository on GitHub; these links point at the commit this page was built from.
- LayoutPAMI-Power_Board.kicad_pcb
- SchematicPAMI-Power_Board.kicad_sch
Micro ROSbot: common questions
What microcontroller does the Micro ROSbot use?
The Micro ROSbot is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.
How big is the Micro ROSbot PCB?
The Micro ROSbot measures 98.7 × 96.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Micro ROSbot?
126 components, from 81 distinct parts. The full bill of materials is listed on this page.
Where can I download the Micro ROSbot design files?
From the emericarhantdev/micro_ROSbot repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Micro ROSbot design in my own project?
The repository has no license, so all rights stay with emericarhantdev. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Micro ROSbot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k