Aeroq
EnriqueNeyra·Aeroq·Aeroq Hardware/v3/Aeroq Hardware v3.kicad_pcb
About the Aeroq PCB
Aeroq is an open source ESP32 PCB design by EnriqueNeyra, published on GitHub under the CC-BY-NC-4.0 license. It is a 2-layer board measuring 45 × 45 mm, with 51 components from 20 distinct parts.
Its main chip is the ESP32-C3-MINI-1-N4, from the ESP32 family. Other key parts include the AMS1117-3.3 and SCD40-D-R1. By type, the board carries 25 capacitors, 9 resistors, 7 diodes, 5 ICs, 2 switches and 1 transistor.
It belongs with the sensors, iot & wireless and displays & leds designs in this gallery.
From the project
An Indoor Air Quality Monitor Powered by ESP32, SCD40, and SEN54
The SEN54 cable must connect pin 1 on the PCB to pin 1 on the SEN54. The board's connector uses the same pin order as the sensor (1: 5V, 2: GND, 3: SDA, 4: SCL, 5: GND, 6: NC). A cable that mirrors the pins leaves the sensor unpowered; see Troubleshooting.
This project uses PlatformIO, a plugin for VSCode that streamlines ESP32 development. The firmware is written in C++ and targets the ESP32-C3 microcontroller.

Main components on the Aeroq
Aeroq bill of materials (BOM)
51 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ SHOU HAN(首韩) | TYPE-C-SMD_USB4120-03-C | U1 |
| 1 | ESP32-C3-MINI-1-N4 | XCVR_ESP32-C3-MINI-1-N4 | U2 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U3 |
| 1 | SCD40-D-R1 | XDCR_SCD40-D-R1 | U4 |
| 1 | ~ XUNPU(讯普) | CONN-SMD_6P-P1.25_XUNPU_WAFER-GH1.25-6PWB | U5 |
| 1 | Si1308EDL | SOT-323_SC-70 | Q1 |
| 1 | ~ XUNPU(讯普) | FPC-SMD_24P-P0.50_FPC-05FB-24PH20 | FPC1 |
| 2 | ~ XUNPU(讯普) | SW-SMD_L3.9-W3.0-P4.45 | SW1, SW2 |
| 1 | 1N5819WS | D_SOD-323 | D1 |
| 3 | ~ LRC(乐山无线电) | SOD-523_L1.2-W0.8-LS1.6-BI | D2, D3, D4 |
| 3 | MBR0530 | D_SOD-123 | D5, D6, D7 |
| 1 | 10uH/1A | L_1210_3225Metric | L1 |
| 3 | 10uf/25V | C_0603_1608Metric | C1, C6, C9 |
| 7 | 0.1uf/50V | C_0603_1608Metric | C2, C3, C5, C7, C8, C11, C15 |
| 5 | 1uf/50V | C_0603_1608Metric | C4, C20, C21, C22, C25 |
| 10 | 4.7uf/25V | C_0603_1608Metric | C10, C12, C13, C14, C16, C17, C18, C19 +2 |
| 5 | 10k | R_0402_1005Metric | R1, R2, R5, R6, R9 |
| 2 | 5k | R_0402_1005Metric | R3, R4 |
| 1 | 3 | R_0402_1005Metric | R7 |
| 1 | 0.47 | R_0402_1005Metric | R10 |
Aeroq design files
The KiCad project lives in the EnriqueNeyra/Aeroq repository on GitHub; these links point at the commit this page was built from.
Aeroq: common questions
What microcontroller does the Aeroq use?
The Aeroq is built around the ESP32-C3-MINI-1-N4, from the ESP32 family.
How big is the Aeroq PCB?
The Aeroq measures 45 × 45 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Aeroq?
51 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Aeroq design files?
From the EnriqueNeyra/Aeroq repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Aeroq design in my own project?
It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.
Can I test firmware for the Aeroq without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k