ESP32EvalBoard
FordPrfkt·ESP32EvalBoard·board/ESP32Eval/ESP32Eval.kicad_pcb
About the ESP32EvalBoard PCB
ESP32EvalBoard is an open source ESP32 PCB design by FordPrfkt, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 40 × 50 mm, with 32 components from 19 distinct parts.
Its main chip is the ESP32-WROOM-32D, from the ESP32 family. Other key parts include the NCP1117-3.3_SOT223 and FT231XS. By type, the board carries 12 capacitors, 7 resistors, 3 ICs, 3 connectors, 3 diodes and 2 transistors.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Eval Board for ESP32
Main components on the ESP32EvalBoard
ESP32EvalBoard bill of materials (BOM)
32 components, 19 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | NCP1117-3.3_SOT223 | SOT-223-3_TabPin2 | U1 |
| 1 | FT231XS | SSOP-20_3.9x8.7mm_P0.635mm | U2 |
| 1 | ESP32-WROOM-32D | ESP32-WROOM-32 | U3 |
| 2 | BC817 | SOT-23 | Q1, Q2 |
| 1 | USB_B_Mini | USB_Mini-B_Lumberg_2486_01_Horizontal | J1 |
| 2 | Conn_01x15 | PinHeader_1x15_P2.54mm_Vertical | J2, J3 |
| 1 | SW_Flash | SW_SPST_B3S-1000 | SW1 |
| 1 | SW_Reset | SW_SPST_B3S-1000 | SW2 |
| 1 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | RX | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | TX | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3 |
| 3 | 10µF | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C4, C8 |
| 3 | 10nF | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C2, C11, C12 |
| 2 | 47pF | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C3, C5 |
| 3 | 100nF | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C6, C7, C9 |
| 1 | 4,7µF | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C10 |
| 2 | 27R | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R2 |
| 3 | 270R | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R3, R6, R7 |
| 2 | 10k | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R4, R5 |
ESP32EvalBoard design files
The KiCad project lives in the FordPrfkt/ESP32EvalBoard repository on GitHub; these links point at the commit this page was built from.
ESP32EvalBoard: common questions
What microcontroller does the ESP32EvalBoard use?
The ESP32EvalBoard is built around the ESP32-WROOM-32D, from the ESP32 family.
How big is the ESP32EvalBoard PCB?
The ESP32EvalBoard measures 40 × 50 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32EvalBoard?
32 components, from 19 distinct parts. The full bill of materials is listed on this page.
Where can I download the ESP32EvalBoard design files?
From the FordPrfkt/ESP32EvalBoard repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the ESP32EvalBoard design in my own project?
Yes, under the terms of its GPL-3.0 license, which FordPrfkt chose for the repository.
Can I test firmware for the ESP32EvalBoard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k