RC-Car

GIANT-Zera·RC-Car·pcb/rc_car.kicad_pcb

RC-Car PCB layout, top view — open source ESP32 board by GIANT-Zera

About the RC-Car PCB

RC-Car is an open source ESP32 PCB design by GIANT-Zera, published on GitHub under the MIT license. It is a 2-layer board measuring 80 × 64 mm, with 66 components from 42 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the DRV8833PWP, AMS1117-3.3, AP63205WU, ME6211C28M5 and ME6211C12M5. By type, the board carries 21 capacitors, 18 resistors, 10 connectors, 6 ICs, 5 diodes and 3 transistors.

It belongs with the robotics & motion, power & battery and iot & wireless designs in this gallery.

From the project

A small web remote controlled car. Try making it and share with others.

An 80 × 64 mm, 2-layer controller board for the 3D-printed sports car in ../car. You drive it from a phone or PC over Wi-Fi (ESP32-S3) and see through its OV2640 camera. It runs two N20 rear-wheel motors from a DRV8833, a steering servo and head/tail lights from a 5 V buck, and you program it over USB-C. The firmware is in ../firmware.

Rev 1.0 (ESP32-C3, no camera) is kept in archive/rev1.0esp32c3`.

RC-Car, from the project README
From the project README

Main components on the RC-Car

RC-Car bill of materials (BOM)

66 components, 42 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1-N16R8
U1
1
DRV8833PWP
U2
1
AMS1117-3.3
U3
1
AP63205WU
U4
1
ME6211C28M5
U5
1
ME6211C12M5
U6
1
AO3401A
Q1
2
AO3400A
Q2, Q3
1
BATTERY 2S
J1
1
MOTOR L
J2
1
MOTOR R
J3
1
USB-C
J4
1
AUX UART
J5
1
SERVO
J6
1
CAMERA OV2640
J7
1
FRONT LIGHTS
J8
1
REAR LIGHTS
J9
1
PWR SWITCH
J10
1
RESET
SW2
1
BOOT
SW3
Show 22 more
QtyPartRefs
1
SS34
D1
2
B5819W
D2, D3
1
PWR (green)
D4
1
STATUS (blue)
D5
1
6.8uH 3A
L1
1
100uF 16V
C1
3
10uF 25V
C2, C6, C12
5
100nF
C3, C8, C10, C13, C21
1
10nF
C4
1
2.2uF
C5
3
22uF 10V
C7, C14, C15
5
1uF
C9, C17, C18, C19, C20
1
10uF
C11
1
100uF 10V
C16
4
100k
R1, R8, R12, R16
4
10k
R2, R3, R4, R13
1
220
R5
2
5.1k
R6, R7
1
33k
R9
2
1k
R10, R11
2
100
R14, R15
2
150
R17, R18

RC-Car design files

The KiCad project lives in the GIANT-Zera/RC-Car repository on GitHub; these links point at the commit this page was built from.

RC-Car: common questions

What microcontroller does the RC-Car use?

The RC-Car is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.

How big is the RC-Car PCB?

The RC-Car measures 80 × 64 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the RC-Car?

66 components, from 42 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the RC-Car design files?

From the GIANT-Zera/RC-Car repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the RC-Car design in my own project?

Yes, under the terms of its MIT license, which GIANT-Zera chose for the repository.

Can I test firmware for the RC-Car without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards